[RE-wrenches] Lumos LSX250 modules
Benn Kilburn
benn at skyfireenergy.com
Thu Jun 19 21:05:44 PDT 2014
To those who have used the suction cups to help with handling these mods, did you purchase or rent the suction cups?
Any insights to share regarding your choices?
I have a 19kw vertical wall install coming up in a couple weeks.
benn
> On Jun 13, 2014, at 1:42 PM, Corey Shalanski <cshalanski at joule-energy.com> wrote:
>
> Chris,
>
> We have done a few Lumos projects down here in the Gulf South, where snow removal is not an issue. Please see attached for an example rooftop installation - these modules definitely end up looking pretty "slick".
> ᐧ
>
> I would echo August's comment about the rail alignment. The module mounting holes allow for a bit of wiggle room, enough to square up any off-kilter modules but not enough to make up for misaligned/non-parallel rails. I would also highly recommend the slotted rails (don't know if the non-slotted rails are even still an option).
>
> As you pointed out wire management is simplified with their rails. Wires running perpendicular to the rails can be accommodated by removing one or more of the rubber bumpers to create a gap between the module and rail. We have also used suction cups to assist in lifting these modules to the roof - at 60 pounds apiece they are noticeably heavier that most of other modules we deal with.
>
> --
> Corey Shalanski
> Joule Energy
> New Orleans, LA
>
>
>> On Fri, Jun 13, 2014 at 12:38 PM, <re-wrenches-request at lists.re-wrenches.org> wrote:
>>
>> Message: 4
>> Date: Thu, 12 Jun 2014 13:34:44 -0700
>> From: August Goers <august at luminalt.com>
>> To: RE-wrenches <re-wrenches at lists.re-wrenches.org>
>> Subject: Re: [RE-wrenches] Lumos LSX250 modules
>> Message-ID: <0159cb59674b658f52fe85632f56bc3b at mail.gmail.com>
>> Content-Type: text/plain; charset="utf-8"
>>
>> Hi Chris,
>>
>>
>>
>> We have a complex 86 kW commercial job with Lumos 250s we?ve just kicked
>> off. We have not installed them yet so I can?t offer a whole lot of advice
>> except that the module leads won?t reach each other in landscape
>> orientation so I?d recommend a standard portrait layout. The rails also
>> need to line up perfectly since the modules mount with the four
>> through-holes.
>>
>>
>>
>> We will be landing our panels in about 3 weeks so I should know more then,
>> feel free to ping me if you haven?t made your decision yet.
>>
>>
>>
>> Best,
>>
>>
>>
>> August
>>
>> Luminalt
> <Lumos Installation.jpg>
> _______________________________________________
> List sponsored by Redwood Alliance
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change listserver email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out or update participant bios:
> www.members.re-wrenches.org
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140619/776ca227/attachment-0002.html>
More information about the RE-wrenches
mailing list