ground rod question [RE-wrenches]
Jason Lerner
wapalco at gmail.com
Tue May 30 21:32:46 PDT 2006
<x-flowed>
Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Is your computer freezing up or slowing down?
Repair corrupt files and harmful errors - protect your PC
Take a 2-minute PC health check-up at no charge!
http://click.topica.com/caaePuwbz8Qcsbz9JC9a/PC Powerscan
-------------------------------------------------------------------
Wrenches,
Randy's comment about taking a chunk out of his thumb pounding ground
rods reminds me of all the times I have missed with the sledge I am
still using (on it's third handle). The only trick I have learned
for pounding a rod when there is nobody around, or nobody around
brave enough to hold it while I swing, is to tie a piece of twine
around the rod and then to a belt loop. Swing, lean back, swing,
lean back. It looks funny, but does help with the wiggle sometimes.
Jason Lerner
Waldron Power and Light Co.
On May 30, 2006, at 8:12 PM, Randy Brooks wrote:
> Your free subscription is supported by today's sponsor:
> -------------------------------------------------------------------
> Is your computer freezing up or slowing down?
> Repair corrupt files and harmful errors - protect your PC
> Take a 2-minute PC health check-up at no charge!
> http://click.topica.com/caaePuwbz8Qcscje7m4a/PC Powerscan
> -------------------------------------------------------------------
>
> Wrenches,
>
> We've also tried the hammer drill, and even a portable jack hammer,
> with limited success. I have worked with other electricians that
> used the demolition hammer with good success in really hard
> ground. I've also driven too many ground rods with the good old
> standby metal fence post driver - and watched the end curl up 3'
> down slope :), broken the end out of the driver and had it welded
> back together, and missed the rod and taken a chunk out of my
> thumb, right through my glove. Be careful out there!
>
> Geoff's item about the air compressor powered tunneling tool
> reminded me of a trick I've used to tunnel under sidewalks. Attach
> a hose to a length of copper or galvanized pipe long enough to
> tunnel to your objective. Turn on the water and let it bore ahead
> of the pipe as you push it through. Took about 30 seconds to go
> through the dirt under a 4' sidewalk. Left a hole plenty big
> enough to push conduit or pull direct burial wire through.
>
> The other tool I haven't seen mentioned is the large Sears tool box
> with wheels and extending handle. They are about 30" wide x 18"
> deep and 24" high. They are sometimes on sale for $30 or $40.
> It's great to wheel a heavy tool box around when possible, and they
> have a big sturdy handle for lifting into the truck.
>
> Randy Brooks
> Brooks Solar, Inc.
> Solar Power for People
> 140 Columbia View
> Chelan, WA 98816
> 509-682-9646
> info at BrooksSolar.com
> www.BrooksSolar.com
>
> --
> [Non-text portions of this message have been removed]
>
>
> - - - -
> To send a message: RE-wrenches at topica.com
>
> Archive of previous messages: http://lists.topica.com/lists/RE-
> wrenches/read
>
> List rules & how to change your email address: www.mrsharkey.com/
> wrenches/etiquette.php
>
> Check out participant bios: www.mrsharkey.com/wrenches/
>
> Hosted by Home Power magazine
>
> Moderator: michael.welch at homepower.com
>
>
- - - -
To send a message: RE-wrenches at topica.com
Archive of previous messages: http://lists.topica.com/lists/RE-wrenches/read
List rules & how to change your email address: www.mrsharkey.com/wrenches/etiquette.php
Check out participant bios: www.mrsharkey.com/wrenches/
Hosted by Home Power magazine
Moderator: michael.welch at homepower.com
--^----------------------------------------------------------------
This email was sent to: michael.welch at homepower.com
EASY UNSUBSCRIBE click here: http://topica.com/u/?bz8Qcs.bz9JC9.bWljaGFl
Or send an email to: RE-wrenches-unsubscribe at topica.com
For Topica's complete suite of email marketing solutions visit:
http://www.topica.com/?p=TEXFOOTER
--^----------------------------------------------------------------
</x-flowed>
More information about the RE-wrenches
mailing list