Outback MX60 question [RE-wrenches]

Thu Dec 22 17:49:46 PST 2005

Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Is your computer freezing up or slowing down?
Repair corrupt files and harmful errors - protect your PC
Take a 2-minute PC health check-up at no charge!
http://click.topica.com/caaegt3bz8Qcsbz9JC9a/PC PowerScan
-------------------------------------------------------------------

Allen - 

I am sorry to hear of your problem with one of our MX60 controllers. I 
trust that the repaired/replacement unit is working well.  

We did have an issue with the Atmel microcontrollers about a year ago.  
We responded quickly to the problem - shutting down all MX60 production 
and putting all of our engineering resources on the problem for about 
three weeks.  We identified the hardware issue and came up with a fix 
for it in the microcontroller software code.  Extensive in house testing 
completed on a 24 hour basis for over a week proved the fix and we began 
shipping again.  All available stock in North America  at our 
distributors was brought back to Arlington for reflashing of the code 
and retesting to ensure proper performance.  Product at our 
international distributors was upgraded at their locations.  

As far as when this issue with the Atmel processors started - we are not 
sure.  We do not get the processors from Atmel in a certain order  - 
i.e.  a delivery of processors can have some from one "batch"   mixed up 
with other "batches" which did not have this issue.  Atmel has not been 
helpful with this problem and, to my knowledge, still denies any problem 
even though we gave them the data showing it.  

So - I understand your pain regarding the cost of the repair - we also 
spent over $100,000 on this issue and are not being compensated either.  
We are, of course, honoring the warranty on any units which fail.  The 
experience so far suggests that the unit will most likely fail under 
cloudy conditions often at lower power levels and it will typically 
happen within the first year of operation.  We have seen less than 10% 
of the units built in the period just prior to the software fix affected 
by this problem.  

We are willing to discuss compensation for any warranty or even 
non-warranty problems with any dealer who feels it is justifed on a 
case-by-case basis.  We do have to draw the line at excessive travel 
costs as that is really an issue the customer has to be responsible for 
themselves.  

I wish there was a simple solution to identify the MX60s which will be 
affected by this issue - but there just is not a simple way to identify 
them.  If the controller is operating correctly for the warranty period 
it is most likely to not have the issue and should operate successfully 
for many, many years.  

We will upgrade the firmware of any MX60s at no charge and we also will 
pay for the return shipping as well.  Please contact us for an RMA 
number prior to shipping to ensure that the unit is handled promptly 
when it shows up here.  You will need to have the serial number of the 
MX60 controller in order to get an RMA number.  Early MX60 controllers 
can also be upgraded to include the data logging system for an 
additional charge.  

We all at OutBack appreciate the support and understanding nature of the 
wrench community.  We hope everyone has an enjoyable and safe holiday. 

Christopher

Christopher Freitas
OutBack Power Systems, Inc.
cfreitas @ outbackpower.com  
www.outbackpower.com
Arlington WA USA
Tel 360 435 6030  

Allan Sindelar wrote:
> 
> Wrenches,
> We recently had an in-warranty MX60 failure, and given the explanation 
> from
> Outback, I'm posting here to find out if this is a common enough failure 
> for
> us to plan some pre-emptive replacement of a few other MX60s.
> 
> An MX60 in a PS2 offgrid application (1900W 72V array into 48V battery)
> failed and was reported by the customer. He saw blank screen and no 
> output;
> a reboot caused it to actually charge partially. We determined the
> MPPT/voltage conversion had failed, but the straight-through partial
> charging carried the customer along for 5 days until I could get out 
> with a
> replacement. Sent the unit in for repair and got the unit back repaired 
> and
> upgraded.
> 
> A call afterwards requesting explanation of what happened taught me 
> this:
> Outback found a "glitch in the silicone in the Atmel processor". The 
> flaw
> would sometimes short the FETs momentarily when the unit turned on. It 
> also
> in the process welds the relay contacts closed (which is what allowed it 
> to
> charge some even though it had failed).
> 
> I was told that Outback found a firmware reprogram that worked around 
> the
> glitch, and applied it to all controllers after serial #7385 (I think
> they're somewhere around #11,000 now). They also recalled some 
> distributor
> stock to do this repair before they went into the field.
> 
> Who else has had a similar failure? Anyone had more than one? This was 
> an
> expensive callback that was fully on our nickel. Anyone at Outback wish 
> to
> clarify what I have written here? Anybody at Outback wish to offer a 
> recall
> program for MX60s in a certain range, with a reimbursement for the 
> service
> call to do a replacement? (Dream on, solar bozo...)
> 
> Thanks for any responses here.
> Allan at Positive Energy
> 

Your free subscription is supported by today's sponsor:
-------------------------------------------------------------------
Save up to $1,500 on your phone bill with Packet8
Free Activation, Free Equipment & First Month Free!
30-day money back guarantee. 1-877-868-1135
http://click.topica.com/caaegt4bz8Qcsbz9JC9f/ TMONE
-------------------------------------------------------------------

- - - -
To send a message: RE-wrenches at topica.com

Archive of previous messages: http://lists.topica.com/lists/RE-wrenches/read

List rules & how to change your email address: www.mrsharkey.com/wrenches/etiquette.php

Check out participant bios: www.mrsharkey.com/wrenches/

Hosted by Home Power magazine

Moderator: michael.welch at homepower.com
--^----------------------------------------------------------------
This email was sent to: michael.welch at homepower.com

EASY UNSUBSCRIBE click here: http://topica.com/u/?bz8Qcs.bz9JC9.bWljaGFl
Or send an email to: RE-wrenches-unsubscribe at topica.com

For Topica's complete suite of email marketing solutions visit:
http://www.topica.com/?p=TEXFOOTER
--^----------------------------------------------------------------