PS2512 glitches [RE-wrenches]

[Roy Dyngen]

Bruce,

You should not need to reload your parameters at all.  If you press the
"Reset to factory defaults" button at anywhere in the menu except under menu
3 where is states "Press reset now for defaults" the button only performs a
screen refresh.  Have you tried cutting the shield foil in the cable as
Allan mentioned in an earlier post?

-----Original Message-----
From: Bruce Geddes [mailto:b.geddes at clear.net.nz] 
Sent: Thursday, September 25, 2003 3:15 PM
To: RE-wrenches at topica.com
Subject: Re: PS2512 glitches [RE-wrenches]

Hi All,
            I have an installation down here that has the same problem.
SW3024E with the remote cable (SWRC50)  in a seperate conduit but
periodically the disply turns to custard or moves one character to the left!
Only way to clear it is to reset and then reload the operating parameters.
This one is on an island so a boat trip each time.  The inverter panel is
unaffected and operates normally.

Bruce Geddes
PowerOn


----- Original Message -----
From: "Bob Ellison, Alternative Energy Systems" <ellison at gisco.net>
To: <RE-wrenches at topica.com>
Sent: Thursday, September 25, 2003 9:06 PM
Subject: RE: PS2512 glitches [RE-wrenches]


John,
I have seen goofy remotes with the Sw series digital readout getting
scrambled when the customer put both the ac and remote wire in the same
conduit together, It is ok for a while then goes goofy till you unplug it.

Bob

RE. Ellison
Supplier of;
Alternative Energy Systems & Supplies
34642 Countryman Road
Theresa, NY. USA
13691-2076


-----Original Message-----
From: Roy Dyngen [mailto:roy.dyngen at xantrex.com]
Sent: Wednesday, September 24, 2003 3:18 PM
To: RE-wrenches at topica.com
Subject: RE: PS2512 glitches [RE-wrenches]


Hi John,

Did they find something wrong with the remote at Tekris?  Although I have
seen some scrambling on the display of the first run of the units (the
inverter, not remotes), I've never heard of problems with the LED's randomly
flashing.  How much is the output wavering and under what conditions?  I
wonder if the problem has always been with the inverter, not the remote.

Roy Dyngen

-----Original Message-----
From: John Blittersdorf, Cent. VT Solar & Wind [mailto:cvsolar at aol.com]
Sent: Wednesday, September 24, 2003 10:12 AM
To: RE-wrenches at topica.com
Subject: PS2512 glitches [RE-wrenches]


I have a customer with a self installed PS2512.  He has had numerous
problems
with his remote control panel, having sent it for repair twice to Tekris and

now he is having problems with the inverter as well.  He said the LEDs on
the
bottom are randomly flashing, not consistent with the mode it is in and he
has
had the voltage output waver up and down.  I haven't witnessed this
firsthand
or checked the output.  Has anyone had this type of problem with the PS.  I
didn't want to sell it to him in the first place but he didn't want to give
up
his 12V system when he needed sinewave power for his heater.  He is now
buying
a Prosine.  I hope he is not jumping from the frying pan to the fire.  Any
more comments good or bad on the ProSine 2000 watt with charger?

John
CVSolar

--
[Non-text portions of this message have been removed]

- - - -
To send a message: RE-wrenches at topica.com

Archive of previous messages: http://www.topica.com/lists/RE-wrenches/

List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm

Check out participant bios: www.mrsharkey.com/wrenches/index.html

Hosted by Home Power magazine

Moderator: michael.welch at homepower.com

- - - -
To send a message: RE-wrenches at topica.com

Archive of previous messages: http://www.topica.com/lists/RE-wrenches/

List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm

Check out participant bios: www.mrsharkey.com/wrenches/index.html

Hosted by Home Power magazine

Moderator: michael.welch at homepower.com

- - - -
To send a message: RE-wrenches at topica.com

Archive of previous messages: http://www.topica.com/lists/RE-wrenches/

List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm

Check out participant bios: www.mrsharkey.com/wrenches/index.html

Hosted by Home Power magazine

Moderator: michael.welch at homepower.com

- - - -
To send a message: RE-wrenches at topica.com

Archive of previous messages: http://www.topica.com/lists/RE-wrenches/

List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm

Check out participant bios: www.mrsharkey.com/wrenches/index.html

Hosted by Home Power magazine

Moderator: michael.welch at homepower.com

- - - -
To send a message: RE-wrenches at topica.com

Archive of previous messages: http://www.topica.com/lists/RE-wrenches/

List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm

Check out participant bios: www.mrsharkey.com/wrenches/index.html

Hosted by Home Power magazine

Moderator: michael.welch at homepower.com
--^----------------------------------------------------------------
This email was sent to: michael_welch at sbcglobal.net

EASY UNSUBSCRIBE click here: http://topica.com/u/?bz8Qcs.bz9JC9.bWljaGFl
Or send an email to: RE-wrenches-unsubscribe at topica.com

TOPICA - Start your own email discussion group. FREE!
http://www.topica.com/partner/tag02/create/index2.html
--^----------------------------------------------------------------