third Party Installations [RE-wrenches]

Joel Davidson joeldavidson at earthlink.net
Wed Nov 7 09:31:46 PST 2001


PV manufacturers and distributors can not grow their reseller customer base
by selling to their customers' customers. Smart wholesalers know that
reseller loyalty is fragile. An apology can usually mend the occasional
mistake. An old, successful distributor in the Maryland area? Gosh, I wonder
who that could be?

Installers can nip distributor "sell-arounds" in the bud by "tagging" your
prospects. Send a copy of your customer correspondence to your trustworthy
distributor. I started doing this in 1983 when Arco Solar sold a 25 kW
system direct to my prospect. Since then I've been on both sides of the
table and, except for occasional mistakes, haven't had a serious problem
since.

"Jason Fisher, Aurora Energy" wrote:

> Rhetorical question but:
> What does the group think of distributors that also operate .coms that
> sell directly to homeowners at dealer prices?
>
> An old, successful distributor in my area does this under two different
> company names: one local, one online. Once I found out about it, I
> stopped buying from them. I wonder if others think that companies like
> this should be held accountable?
>
> Jason Fisher
> Aurora Energy
> Annapolis, Maryland
>
> -----Original Message-----
> From: Joel Davidson [mailto:joeldavidson at earthlink.net]
> Sent: Tuesday, November 06, 2001 1:42 PM
> To: RE-wrenches at topica.com
> Subject: Re: third Party Installations [RE-wrenches]
>
> 1. You could buy equipment from Mr. Solar and resell to your customer.
> Your overall
> profit margin will be smaller, but it may be better than losing the sale
> or losing
> the installation.
>
> 2. Buy the equipment from your regular supplier or another supplier who
> listens to
> your situation and gives you lower prices so you can compete. A wise
> supplier will
> do what he can to can keep your business and help you grow your business
> and his
> business through your sales efforts.
>
> 3. Large volume is just a lot of small volume. A customer who buys 1,000
> solar
> modules per year is an 84 module/month customer. A wise supplier knows
> that
> scheduling and shipping 84 modules/month is better for both the supplier
> and the
> customer. Your supplier knows that you buy X-number of modules per year.
> Ask for a
> volume discount on the annual amount based on your continued business.
>
> 4. It is not bad for the industry to sell things at lower prices to
> volume
> customers.
>
> 5. The "do-it-yourselfer" is your competitor too. But perhaps you can
> win their
> business by guaranteeing higher overall savings by providing a
> comprehensive energy
> audit, energy conservation and efficiency advice that results in a
> smaller PV
> system. Perhaps you can convince customers that they will save time and
> money if
> they hire you to install their system right the first time.
>
> 6. Don't waste your time with owner-installers. Ask prospects up-front,
> "Do you
> want to hire me to install their system or do you plan on installing it
> yourself?"
> If you think that they are a do-it-yourselfer, tell them politely, "From
> what you
> are saying, it sounds like you want to install your own PV system. Our
> company does
> not sell parts to do-it-yourselfers. If you would like us to to install
> your PV
> system, we do have to charge for our time to come to your home or
> business and do a
> site analysis and work up a system design. Our fee is (range in L.A. is
> $100 to
> $300 for site visits up to 1 hour travel time). If you decide to hire us
> to install
> your system, we will credit the full price of our site analysis and
> system design
> work toward the installed price. Would you like to schedule a site visit
> today?"
> (offer and trial close)
>
> 7. Learn how to weed out the suspects from the prospects and qualify
> your
> prospects. Your sales close rate will increase. You will spend less time
> with
> non-customers. You will have more time for yourself and your loved ones.
>
> Drake Chamberlin - Electrical Energy wrote:
>
> > Hi Joel,
> >
> > Mr. Solar can often sell direct to the customer at about the same
> price as
> > we pay.  It apparently takes a large volume purchaser to buy at really
> good
> > prices.
> >
> > In my opinion, this is bad for the industry.  Many people do buy
> equipment
> > at low cost and connect them to dwellings that have pretty standard
> > electrical demands.  Therefore, systems go in that "prove," once
> again,
> > that solar doesn't work.
> >
> > Yet for 20% more on their up front costs, they could have a system
> that
> > would really do something.  Or, in other cases, they might find that
> they
> > don't really need all the equipment they are buying (with the proper
> set
> > up) and could spend the same amount.
> >
> > Drake
> >
> > At 07:54 AM 11/06/2001 -0800, you wrote:
> > >The smart plumber tells his customer, "Sure, I can sell you the Home
> Depot
> > >water
> > >heater at the same price as Home Depot." Then he either buys the
> heater at
> > >Home Depot
> > >or buys it at a discount from another supplier or tells his customer
> why
> > >he should
> > >buy the brand heater that he sells. Plumbers, electricians, PV
> installers,
> > >etc. are
> > >competing with Home Depot and other parts suppliers. So learn how to
> > >compete. Make
> > >your equipment prices competitive. Learn price differentiation.
> Determine your
> > >materials, labor and G&A prices that you need to meet your profit
> goals.
> > >You can not
> > >manage your competition, but you can take manage your own business
> and your
> > >customers.
> > >
> > >
> > >
> > >jay peltz wrote:
> > >
> > > > HI Drake,
> > > >
> > > > Well said.  I keep coming back to our other trades, such as
> electrical or
> > > > plumbing.
> > > >
> > > > How many plumbers will install a hot water heater, that you don't
> buy
> > > from them,
> > > > and how  many would warranty it?  yea right,
> > > >
> > > > How many electricans would  install the same, equipment bought
> elsewhere?
> > > >
> > > > Solar has gotten the rap as being something you can do yourself,
> and so
> > > it is.
> > > > But when you cross that line of oops I can't do it myself  that it
> gets
> > > very
> > > > complicated.  Much of this problem comes from web sellers.  As I
> used
> > > to be one
> > > > for AEE and then Applied power, the hardest part of my job was to
> > > figure the
> > > > design parameters.  The system was easy, but the hows and whys and
> not
> > > being able
> > > > to see and having to trust the customer, next to impossible.
> > > >
> > > > Our industry is no different.  We have good installers, and poor
> > > ones.  Ones who
> > > > understand design, others who only understand profit.  No way to
> make
> > > it perfect,
> > > > its just life.  But hay our time is now!!
> > > >
> > > > jay
> > > >
> > > > peltz power
> > > >
> > > > Drake Chamberlin - Electrical Energy wrote:
> > > >
> > > > > Hi Wrenches,
> > > > >
> > > > > Most of my RE work is with systems that are either off grid, or
> > > designed to
> > > > > supply specified loads in the event power outages.  To function
> > > adequately,
> > > > > these systems require careful planning.  Some of my concerns
> might not
> > > > > apply to systems that are strictly gird intertie.
> > > > >
> > > > > I  am willing to install equipment purchased from other sources
> with
> > > > > certain understandings.  One is that, in the event of equipment
> > > failure, I
> > > > > will be paid my regular rate to service the installation, unless
> the
> > > > > problem is due to my error.
> > > > >
> > > > > A big issue is, that I must be paid for designing the system.
> Without
> > > > > commission, I can't afford to provide "free" deign work.   The
> bargain
> > > > > hound may find that much of his savings are eaten up by having
> to pay for
> > > > > design time.
> > > > >
> > > > > A lot of existing systems I've seen look fine.  A power panel
> hanging
> > > on a
> > > > > wall, and a nice looking solar array can look pretty impressive.
> The
> > > only
> > > > > problem is that many of these systems don't accomplish much.
> The
> > > > > electrical loads and use patterns of the premise may squander
> the
> > > > > relatively few watts available from the PV system.
> > > > >
> > > > > Yet, with a well thought out system, a dwelling really can run
> on solar
> > > > > electricity.  It may require not using a forced air furnace, but
> > > > > circulating DC pumped hot water from a gas boiler, that uses
> either a
> > > pilot
> > > > > light or an efficient AC control box, that is designed to shut
> off
> > > when not
> > > > > needed.  This may require working with a plumber who needs to be
> > > > > educated.  This may lead to searches for appropriate boilers,
> hot water
> > > > > tanks, pumps, tubing and other related equipment.  It may be
> necessary to
> > > > > make certain, that elements of systems that we are not
> installing,
> > > get set
> > > > > up properly.
> > > > >
> > > > > A functional system may require phantom loads be eliminated by
> use of DC
> > > > > powered answering machines, computers, cell phones, etc.
> Voltages may
> > > need
> > > > > to be adjusted by using battery bank equalizers or DC to DC
> voltage
> > > > > converters.
> > > > >
> > > > > All proposed appliances need to be cleared for the system.
> Certain loads
> > > > > may need to be shed on low battery conditions.  Water pumping
> and
> > > > > pressurizing strategies need to be evolved.  Wires need to be
> sized for
> > > > > amperage and voltage drop.  Code compliant physical layouts need
> to be
> > > > > developed, often with difficult space limitations.  Appropriate
> and
> > > > > properly listed equipment needs to be specified and located for
> all
> > > > > subsystems.  It is truly necessary to wholisticly design the
> entire
> > > system,
> > > > > loads as well as generation.
> > > > >
> > > > > Every job is different.  Making an off grid home truly function
> > > involves a
> > > > > lot more than hanging an inverter on a wall and wiring batteries
> &
> > > modules
> > > > > together.  Two systems may look a lot a like to the untrained
> eye,
> > > but one
> > > > > may serve 95% of the electrical needs of a premise and the other
> > > 15%.  The
> > > > > magic is in the subtle detail.  In this line of work, details
> really do
> > > > > matter.
> > > > >
> > > > > I don't care too much how I get reimbursed for my time.  It is
> probably a
> > > > > better deal for the customer to pay the higher price for the
> > > equipment, and
> > > > > get on-going support for the system, plus get the "free" design
> > > work.  But
> > > > > it is sometimes hard to get customers to understand that there
> is more to
> > > > > this business than assembling a Lego set.  That can be the
> biggest
> > > > > challenge in a project.  But careful design work is essential to
> > > > > demonstrate the true potential of PV.   Few can afford to supply
> it
> > > for free.
> > > > >
> > > > > Peace,
> > > > >
> > > > > Drake
> > > > >
> > > > > - - - -
> > > > > To send a message: RE-wrenches at topica.com
> > > > >
> > > > > Archive of previous messages:
> http://www.topica.com/lists/RE-wrenches/
> > > > >
> > > > > List rules & etiquette:
> http://www.mrsharkey.com/wrenches/etiquete.htm
> > > > >
> > > > > Check out participant bios:
> www.mrsharkey.com/wrenches/index.html
> > > > >
> > > > > Hosted by Home Power magazine
> > > > >
> > > > > Moderator: michael.welch at homepower.com
> > > > >
> > > >
> > > > - - - -
> > > > To send a message: RE-wrenches at topica.com
> > > >
> > > > Archive of previous messages:
> http://www.topica.com/lists/RE-wrenches/
> > > >
> > > > List rules & etiquette:
> http://www.mrsharkey.com/wrenches/etiquete.htm
> > > >
> > > > Check out participant bios: www.mrsharkey.com/wrenches/index.html
> > > >
> > > > Hosted by Home Power magazine
> > > >
> > > > Moderator: michael.welch at homepower.com
> > > >
> > >
> > >- - - -
> > >To send a message: RE-wrenches at topica.com
> > >
> > >Archive of previous messages:
> http://www.topica.com/lists/RE-wrenches/
> > >
> > >List rules & etiquette:
> http://www.mrsharkey.com/wrenches/etiquete.htm
> > >
> > >Check out participant bios: www.mrsharkey.com/wrenches/index.html
> > >
> > >Hosted by Home Power magazine
> > >
> > >Moderator: michael.welch at homepower.com
> > >
> >
> > - - - -
> > To send a message: RE-wrenches at topica.com
> >
> > Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
> >
> > List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
> >
> > Check out participant bios: www.mrsharkey.com/wrenches/index.html
> >
> > Hosted by Home Power magazine
> >
> > Moderator: michael.welch at homepower.com
> >
>
> - - - -
> To send a message: RE-wrenches at topica.com
>
> Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
>
> List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
>
> Check out participant bios: www.mrsharkey.com/wrenches/index.html
>
> Hosted by Home Power magazine
>
> Moderator: michael.welch at homepower.com
>
> - - - -
> To send a message: RE-wrenches at topica.com
>
> Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
>
> List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
>
> Check out participant bios: www.mrsharkey.com/wrenches/index.html
>
> Hosted by Home Power magazine
>
> Moderator: michael.welch at homepower.com
>

- - - -
To send a message: RE-wrenches at topica.com

Archive of previous messages: http://www.topica.com/lists/RE-wrenches/

List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm

Check out participant bios: www.mrsharkey.com/wrenches/index.html

Hosted by Home Power magazine

Moderator: michael.welch at homepower.com

==^================================================================
This email was sent to: michael.welch at homepower.com

EASY UNSUBSCRIBE click here: http://topica.com/u/?bz8Qcs.bz9JC9
Or send an email to: RE-wrenches-unsubscribe at topica.com
<A HREF=" http://topica.com/u/?bz8Qcs.bz9JC9 ">
AOL users click here.</A>

T O P I C A -- Register now to manage your mail!
http://www.topica.com/partner/tag02/register
==^================================================================





More information about the RE-wrenches mailing list