becoming an inter-tie system [RE-wrenches]
jay peltz
jay at asis.com
Sun Feb 18 15:00:19 PST 2001
Hi All,
APC used to carry a box made for the GFI.
#53-531-167
You can also get it with an additional plate so that you can install
standard CD ( smaller style)Heinimen breakers.
If they don't have it I know that it was made from Two Seas, they might
have some or make them. They were powder coated white, worked well.
Jay
Peltz Power
Redway CA
"Bob-O Schultze, Electron Connection" wrote:
> Hiya Larry,
> Ah, the DC GFP! A device invented to fill a requirement written to
> correct a situation for which there was never a problem in the first
> place!
> Trace has the only one I know about. Roll your own can. I use them in
> 48V systems every time (which ain't often because I try like hell to
> talk folks out of putting PVs on roofs, but sometimes you gotta) In
> 24V systems I voice my opinions to the client and give them the
> choice knowing that they may have to pay me to install one later on
> IF the inspector requires it. What's the difference? Lifeform
> protection. There are no recorded instances of folks getting
> electrocuted by voltages less than 42VDC. Above that could, under the
> worst case scenario, potentially zap someone.
> Best, bob-O
>
> >Wrenches, I have a system on a customers house that consists of 4
> >SP75's roof mounted, a 4024 with a DC 250 disconnect, a C-40 charge
> >controller and 8 T-105's. This is a grid connected house and we set
> >up a separate subpanel for the loads that run off the 4024. The
> >grid feeds AC1 and acts as the back up. Therer is no generator on
> >this system. This system was always intended to grow as the
> >customers budget could afford. Now we are adding 12 more SP75's on
> >the roof and they are going to inter-tie with the grid. We will add
> >an outside disconnect to comply with requirements. The question is
> >about GFI protection for the roof mounted array. What has anyone
> >been doing to provide for GFI protection for roof mounted arrays?
> >and where in the control room equipment has anyone mounted the GFI
> >protection? There is a 60 amp DC breaker mounted in the DC250 from
> >the array on the way to the C-40
> >Thanks for any feedback
> >
> >Larry Brown
> >Sun Mountain
>
> - - - - - - -
> To send a message:
> RE-wrenches at topica.com
>
> The archive of previous messages:
> http://www.topica.com/lists/RE-wrenches/
>
> List rules & etiquette:
> http://www.mrsharkey.com/wrenches/etiquete.htm
>
> To unsubscribe send a message to:
> RE-wrenches-unsubscribe at topica.com
>
> To check out the other RE-Wrench participants:
> www.mrsharkey.com/wrenches/index.html
>
> Hosted by Home Power magazine:
> www.homepower.com
>
> For info contact list moderator by email:
> michael.welch at homepower.com
>
> ____________________________________________________________
> T O P I C A -- Learn More. Surf Less.
> Newsletters, Tips and Discussions on Topics You Choose.
> http://www.topica.com/partner/tag01
- - - - - - -
To send a message:
RE-wrenches at topica.com
The archive of previous messages:
http://www.topica.com/lists/RE-wrenches/
List rules & etiquette:
http://www.mrsharkey.com/wrenches/etiquete.htm
To unsubscribe send a message to:
RE-wrenches-unsubscribe at topica.com
To check out the other RE-Wrench participants:
www.mrsharkey.com/wrenches/index.html
Hosted by Home Power magazine:
www.homepower.com
For info contact list moderator by email:
michael.welch at homepower.com
____________________________________________________________
T O P I C A -- Learn More. Surf Less.
Newsletters, Tips and Discussions on Topics You Choose.
http://www.topica.com/partner/tag01
More information about the RE-wrenches
mailing list