Dual DR's [RE-wrenches]
jay peltz
jay at asis.com
Mon Dec 18 11:09:40 EST 2000
Hi John,
Also you can stack models of different sizes. Trace doesn't advertise it but I
learned from one of the head engineers that you can stack a 1524 and a 3624.
With the large one for the loads of the house and the combined for the well pump.
I agree that they do work well for houses but I find that most people want the
"options" and so the SW. I wonder where the compitition is for that one??
jay peltz
Peltz Power
"John Blittersdorf, Cent. VT Solar & Wind" wrote:
> Hi Wrenches,
> As I sit on my rain and wind swept mountainside listening to Prairie Home
> Companion, I am thinking of ways to provide budget systems for the poorer
> folks in the area who need to run well pumps (fairly common in this area). I
> have been testing the DR1524 running my house for the last two weeks and so
> far I am quite impressed with the results. I have run all house lights,
> stereo and TV, computer and propane furnace(450 watts-manually switching
> blower on as the mod square will not work the controller) and my wife asked
> me if she could turn on the microwave. I guess I like living on the edge so
> I said OK and continued the test of an inverter that is already sold... to be
> installed next week. So far, no problems. It does seem to be sluggish at
> charge rate from a 2200 watt generator which according to the documentation
> for the DR is normal. It will be running off a 3600 watt Honda in its
> permanent home and should charge somewhat better.
>
> Since this is the least expensive DR inverter, and Trace says it will handle
> 3500 watts for 1 minute, what do you think about using dual stacked DR1524's
> to run a well pump. Has anyone done this or with the bigger DR's. This
> would be cheaper than a PS2512 and theoretically could deliver more power.
>
> Another question. Has anyone used Tekris Power Electronics, Inc in New
> Jersey for repairs of Trace inverters. I have an SW4024 on its way to them
> for repair. They were recommended by Trace's repair dept in Arlington WA and
> Chris from Tekris has been extremely responsive to questions emailed to him.
>
> Another DR1524 test note. I am running my breadmaker, two computers, house
> lights and stereo with good results. I do notice a little voltage drop when
> the breadmaker heating element kicks on but otherwise it is quite steady.
> Since I am planning to get rid of the propane furnace at some point, I am
> seriously considering downsizing to a DR1524 for a long term test. I like
> the idea of the 8.4 watt idle load.
>
> I'm starting to sway from my previous philosophy of standardizing and selling
> everyone an SW4024 when possible. I guess it is the dilemma of efficiency
> and marginality vs more income and robustness. I guess I should get back to
> work before I drive myself nuts with these questions.
>
> John
> CVSolar
> Powered tonight by a BWC1500.
>
> - - - - - - -
> To send a message:
> RE-wrenches at topica.com
>
> The archive of previous messages:
> http://www.topica.com/lists/RE-wrenches/
>
> To unsubscribe send a message to:
> RE-wrenches-unsubscribe at topica.com
>
> To check out the other RE-Wrench participants:
> www.mrsharkey.com/wrenches/index.html
>
> Hosted by Home Power magazine:
> www.homepower.com
>
> For info contact list moderator by email:
> michael.welch at homepower.com
>
> ___________________________________________________________
> T O P I C A http://www.topica.com/t/17
> Newsletters, Tips and Discussions on Your Favorite Topics
- - - - - - -
To send a message:
RE-wrenches at topica.com
The archive of previous messages:
http://www.topica.com/lists/RE-wrenches/
To unsubscribe send a message to:
RE-wrenches-unsubscribe at topica.com
To check out the other RE-Wrench participants:
www.mrsharkey.com/wrenches/index.html
Hosted by Home Power magazine:
www.homepower.com
For info contact list moderator by email:
michael.welch at homepower.com
___________________________________________________________
T O P I C A http://www.topica.com/t/17
Newsletters, Tips and Discussions on Your Favorite Topics
More information about the RE-Wrenches
mailing list