[RE-wrenches] midnite new inverter

[William Bryce]

John

The New MidNite AIO is completely field serviceable. If you have an
issue (say lightning) MNS will stock all the needed boards and everything
can be replaced on the wall.
On a scale of one to ten, it's a 7 with 10 being the hardest (lots of
screws). Only tools needed are an 11in One, pliers, and some hex wrenches.

I am a Beta tester.

Logan




On Wed, Apr 10, 2024 at 9:49 AM Howie Michaelson via RE-wrenches <
re-wrenches at lists.re-wrenches.org> wrote:

> John,
> If you are thinking of pairing the Envy with lead-acid batteries, I would
> strongly suggest not doing it. Even though Fortress sales advertises the
> Envy to be compatible with lead-acid, after trying it in my off-grid home,
> I would emphatically say that it is not. The programming is inadequate, to
> put it kindly. And their support really doesn't have a clue about lead-acid
> - Fortress support literally said that they don't recommend pairing the
> Envy with l-a. However, I don't have an opinion about how it does with
> closed loop Li batteries.
> I did recently install an EG4 18k system, off-grid, with the client's
> knowledge that this was a bit of an experiment for me. Both the Envy and
> the EG4 are made by LuxPower and have been, to date, physically and
> programmatically almost identical. I had stayed away from EG4 since it
> seemed to be primarily aimed at the DIY market. However, the 18k appears to
> be a serious contender so far, although this installation is a fairly low
> stress situation. I've been fairly impressed with the system.   While this
> 18k is paired with EG4 Lithium batteries, EG4 has been making adjustments
> to the firmware to make it much more friendly to lead-acid. If you decide
> to go this route, check with EG4 (installer support - ask for Jarrett or
> Colt) to see where they are at with upgrading the firmware.
> I am also eagerly awaiting Midnite's AIO entry...
>
> Howie
>
>
> On Wed, Apr 10, 2024 at 9:02 AM John Blittersdorf via RE-wrenches <
> re-wrenches at lists.re-wrenches.org> wrote:
>
>> Time will tell where the failure modes are.   I still don't like all the
>> eggs in one basket. Do you have to send the units back for repair?  Had
>> enough of that with Trace SW series inverters..
>> For off grid, I'll stick to the tried and true for now.  For Grid tie it
>> is just a financial hit.  For off-grid power loss it is more important
>> to deal with right away..
>>
>> I am going to try a Fortress Envy at my off grid home but will keep my
>> Outback field repairable VFXR wired in just in case. I had a massive
>> lightning strike between my house and a guest cabin 1/4 mile away and I
>> lost power from my Fortress Eflex battery at the cabin and my Outback
>> inverter at my house.  I replaced the control board on my inverter ( I
>> always keep one in reserve as it is usually the only board failure due to
>> lightning)  and was back on line in 1/2 hour and Fortress rushed me a new
>> BMS board for the E-flex and a day later and a half hour swap had it back
>> in service,  Now it is a different story with 2 Simpliphi batteries I have
>> from a customer that failed.  I have to ship them to California to have
>> them evaluated to see if we had damaged them by misuse.  Lots of expense
>> and time lost.
>>
>>
>>
>> John Blittersdorf
>> CV Wind Service / Off Grid Vermont
>> 802-770-8625
>>
>> On Tue, Apr 9, 2024 at 11:43 PM Scot Arey via RE-wrenches <
>> re-wrenches at lists.re-wrenches.org> wrote:
>>
>>> Wow, are we in the golden age of inverter/chargers? If it had 200-a.p
>>> pass thru it would be near perfect.
>>>
>>> Begs the question: are stand alone charge controllers becoming a
>>> historical artifact?
>>>
>>> Howard "Scot" Arey
>>> Owner, Solar CenTex
>>> 254-300-1228
>>> _______________________________________________
>>> List sponsored by Redwood Alliance
>>>
>>> Pay optional member dues here: http://re-wrenches.org
>>>
>>> List Address: RE-wrenches at lists.re-wrenches.org
>>>
>>> Change listserver email address & settings:
>>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>>>
>>> There are two list archives for searching. When one doesn't work, try
>>> the other:
>>> https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
>>> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>>>
>>> List rules & etiquette:
>>> http://www.re-wrenches.org/etiquette.htm
>>>
>>> Check out or update participant bios:
>>> http://www.members.re-wrenches.org
>>>
>>> _______________________________________________
>> List sponsored by Redwood Alliance
>>
>> Pay optional member dues here: http://re-wrenches.org
>>
>> List Address: RE-wrenches at lists.re-wrenches.org
>>
>> Change listserver email address & settings:
>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>>
>> There are two list archives for searching. When one doesn't work, try the
>> other:
>> https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
>> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>>
>> List rules & etiquette:
>> http://www.re-wrenches.org/etiquette.htm
>>
>> Check out or update participant bios:
>> http://www.members.re-wrenches.org
>>
>> _______________________________________________
> List sponsored by Redwood Alliance
>
> Pay optional member dues here: http://re-wrenches.org
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change listserver email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> There are two list archives for searching. When one doesn't work, try the
> other:
> https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> http://www.re-wrenches.org/etiquette.htm
>
> Check out or update participant bios:
> http://www.members.re-wrenches.org
>
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20240410/dfea6d86/attachment.htm>