[RE-wrenches] Old and new Radian

Michael Morningstar mjmorningstar at gmail.com
Wed May 10 18:48:19 PDT 2023


I just pulled out an 8048 and replaced it with a 8048A due to the lack of
AC boards for 8048s. I didn't know any better and put in a new 8048A board
and learned the hard way that they aren't cross compatible. Smoked it. If
you think you can find a board for it, it's yours.

On Wed, May 10, 2023 at 11:06 AM Darryl Thayer via RE-wrenches <
re-wrenches at lists.re-wrenches.org> wrote:

> Sorry if this is nonsense,  but your existing Radian is your "AC grid
> source," It can act as the paralleling.
> AC coupling source.  I did this about 20 to 30 years ago, using FX
> inverters, not Radians, to power a large motor.
> Can your Radian Mate 3 run in grid zero? Or if not, one inverter runs all
> the time as a grid source ( grid forming)
> the second inverter (grid following) runs in Grid-Zero mode, with
> "off-set" set at 30 Amps.  If the load is less than 30 amps,
> the grid-following inverter carries the load.  (The grid-forming inverter
> supplies the grid signal, and the following inverter
> carries the load.)  When your load exceeds 30 amps, the extra current
> comes from the grid-forming inverter.  The Radian can
> pass up to 50 or 60 amps from the forming inverter.  You can get 50 to 60
> amps
> to the load when you add the forming and following inverters.  Errors:
> this will double your parasitic load, I have not done this
> so beware.  This is not the answer for V2H; other inverters can work in
> this combination but
>
>
> On Wed, May 10, 2023 at 10:04 AM frenergy via RE-wrenches <
> re-wrenches at lists.re-wrenches.org> wrote:
>
>>          The wrench list has some very creative thinkers that may have a
>> go around to be able to master/slave an old Radian's output with a new
>> one.   Outback says this is not do-able.   We're completely off-grid out
>> here and have been charging EVs (one at a time) with an eleven year old
>> Radian (GS8048) for years but the Ford Lightning is on its way.  Outback
>> says I can't add the newer GS8048A to exiting version (no "A").
>>
>> Ideas??
>>
>> Bill
>>
>> Feather River Solar Electric
>> Bill Battagin, Owner
>> 4291 Nelson St.(shipping)
>> 5575 Genesee Rd. (USPS, UPS)
>> Taylorsville, CA 95983
>> 530.284.1925 Office/ 530.258.1641 Cell
>> CA Lic 874049
>> Solar powered since 1982
>>
>>
>> --
>> This email has been checked for viruses by Avast antivirus software.
>> www.avast.com
>> _______________________________________________
>> List sponsored by Redwood Alliance
>>
>> Pay optional member dues here: http://re-wrenches.org
>>
>> List Address: RE-wrenches at lists.re-wrenches.org
>>
>> Change listserver email address & settings:
>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>>
>> There are two list archives for searching. When one doesn't work, try the
>> other:
>> https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
>> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>>
>> List rules & etiquette:
>> http://www.re-wrenches.org/etiquette.htm
>>
>> Check out or update participant bios:
>> http://www.members.re-wrenches.org
>>
>> _______________________________________________
> List sponsored by Redwood Alliance
>
> Pay optional member dues here: http://re-wrenches.org
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change listserver email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> There are two list archives for searching. When one doesn't work, try the
> other:
> https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> http://www.re-wrenches.org/etiquette.htm
>
> Check out or update participant bios:
> http://www.members.re-wrenches.org
>
>

-- 

Michael Morningstar


Morningstar Electric

PO Box 1494

Mount Shasta, CA 96067

530-921-0560

mjmorningstar at gmail.com
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20230510/3e122b3b/attachment.htm>


More information about the RE-wrenches mailing list