[RE-wrenches] Kyocera 120's low voltage
Christopher Warfel
cwarfel at entech-engineering.com
Thu Jun 12 04:54:35 PDT 2014
Same here. Kyocera was very good at providing replacements and covering
reasonable labor.
On 6/11/2014 8:20 PM, Jerry Shafer wrote:
> David
> The KC 120 had some issues with soldered connections on the module
> looks like a cigarette burn from the back or maybe just a blister, it
> will be on the shrt side of the module. Anyway it will drop the module
> in half most of the time or try to work while it burns the poorly
> soldered connection, it will also get bery hot as it is arcing inside.
> You need the SN# and call the manufacture if its on there list it
> might be replaceble they can tell you. As I recall its a C that is the
> SN that has an issue but check to make sure.
> I have replaced entire arrays because of this.
>
>
> On Wed, Jun 11, 2014 at 4:47 PM, Dave <dave at independentpowerllc.com
> <mailto:dave at independentpowerllc.com>> wrote:
>
> Wrenches,
>
> I troubleshot an underperforming off grid array today and found
> low Voc's in 4 out of 10 KC-120's (nominal 12v modules rated at
> 21.5 Voc and 7.45 Isc). Modules are vintage 2000.
>
> Under modest sunlight (500 to 600W per M sqd) 6 modules measured
> from 18 to 19 Voc and 4 Isc. Four modules measured from 9.6 to
> 13.7 Voc and 4 Isc.
>
> I was chased off the roof by a coming thunderstorm and did not
> check for bad diodes. These modules have nice old school J-boxes
> with 6 diodes per each module.
>
> Am I looking at a diode issue, or failing modules?
>
> Thanking you in advance for your time,
>
> David Palumbo
>
> Independent Power LLC
>
> 462 Solar Way Drive
>
> Hyde Park, VT 05655
>
> 802-888-7194 <tel:802-888-7194>
>
>
> _______________________________________________
> List sponsored by Redwood Alliance
>
> List Address: RE-wrenches at lists.re-wrenches.org
> <mailto:RE-wrenches at lists.re-wrenches.org>
>
> Change listserver email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive:
> http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
> <http://www.re-wrenches.org/etiquette.htm>
>
> Check out or update participant bios:
> www.members.re-wrenches.org <http://www.members.re-wrenches.org>
>
>
>
>
>
> _______________________________________________
> List sponsored by Redwood Alliance
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change listserver email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out or update participant bios:
> www.members.re-wrenches.org
>
--
Christopher Warfel, President
ENTECH Engineering, Inc.
PO Box 871, Block Island, RI 02807
401-466-8978
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140612/da10fd0e/attachment-0002.html>
More information about the RE-wrenches
mailing list