[RE-wrenches] Stainless NEMA4x load center, SolarDeck w/ breakers
Chris Mason
cometenergysystems at gmail.com
Wed Apr 23 15:00:32 PDT 2014
The Midnite Solar MNPVHV Disconnecting combiners can be installed at 45
degrees. We just used on and they are very watertight and very nicely made.
On Wed, Apr 23, 2014 at 12:01 PM, Chris Schaefer
<chris at solarandwindfx.com>wrote:
> Jason,
>
> I love the picture. Just ran into this a few days ago on an
> install. Had two older SolarDeck Model 0780 in stock. I had the same two
> pole breakers and attempted to install them here in the shop before I went
> out to the project as I was afraid their height would not allow the cover
> to seal. And it did not. It appears you have ABB breakers and I just tried
> them and they don’t fit either. Now if you look at your link it shows and
> states fuse holders, which do fit. I’m wondering if the newer models in
> your link are just a little bit taller than the older models I had in
> stock. I don’t see size specs on their web site. Can you please provide the
> model# you show in your photo?
>
>
>
> Christopher Schaefer
>
> Chris Schaefer’s
>
> [image: SolarWindFX]
>
> * Tel/Fax 585-229-2083 <585-229-2083> or Cell
> 585-748-1870 <585-748-1870> *
>
> * 5115 South Hill Road ~ Canandaigua New York 14424*
>
> *www.solarandwindfx.com <http://www.solarandwindfx.com> ~ E-mail:
> chris at solarandwindfx.com <chris at solarandwindfx.com>*
>
>
>
>
>
>
>
>
>
>
>
>
>
> Thomas Jefferson, the author of our great Constitution, once said,
> "democracy" will cease to
> exist
> when you take away from those who are willing to work
> and give to those who would not."
>
>
>
> *From:* re-wrenches-bounces at lists.re-wrenches.org [mailto:
> re-wrenches-bounces at lists.re-wrenches.org] *On Behalf Of *Jason Szumlanski
> *Sent:* Wednesday, April 23, 2014 11:36
> *To:* RE-wrenches
> *Subject:* Re: [RE-wrenches] Stainless NEMA4x load center
>
>
>
> See my other response, but you should definitely consider SolaDeck in this
> case. You want SolaDeck Model 0786-41. Make sure you order the correct
> breakers, bus bars, and Neutral terminal block.
>
>
>
>
> http://www.rstcenterprises.com/soladeck/products/1741_combiner_enclosure.phtml
>
>
>
> The attached picture is the Soladeck on my 3-string Enphase system at
> home (note: neutral block was not on DIN rail yet). There are four neutrals
> on the bottom of the N block because I center-fed one inverter string, so I
> had four sets of Enphase cable coming into the box, which is admittedly a
> little tight. If you need to do this, I recommend transitioning to THWN in
> a separate combiner and just bringing in three strings through one or two
> conduits.
>
>
>
>
>
> [image: Inline image 1]
>
>
>
> Jason Szumlanski
>
> Fafco Solar
>
>
>
>
>
>
>
> On Wed, Apr 23, 2014 at 11:17 AM, Kirpal Khalsa <solarworks at gmail.com>
> wrote:
>
> Drake.....we want it to mount flush to the slope of a sloped roof....The
> NEMA 3R are supposed to be mounted vertically....This is for a large
> residential Enphase system and we wanted to combine the circuits on the
> roof and bring one set of conductors down.....
>
> I did find one custom made by Eaton(Cutler Hammer), but....$952 my cost is
> too much..I have had them make me one out of fiberglass in the past but it
> is about 3 years into its roof mount life and showing signs of UV
> degradation...looking for other options....I think i will dig a little
> deeper at Midnite Solar.....They may have something....Theirs and Outback's
> PV combiners are rated to be mounted at a slope....i think it is down to 14
> degrees pitch (3/12)
>
> Thanks.
>
>
> Sunny Regards,
> Kirpal Khalsa
> NABCEP Certified PV Installation Professional
> Renewable Energy Systems
> www.oregonsolarworks.com
>
> 541-218-0201 m
> 541-299-0402 o
>
>
>
> On Wed, Apr 23, 2014 at 8:11 AM, Drake <
> drake.chamberlin at redwoodalliance.org> wrote:
>
> That would be a nice piece of hardware. Is there any reason you can't use
> a NEMA 3R panel? They are used on roofs quite a bit, and are readily
> available. The Square D, 8 space, outdoor box should work in most rooftop
> environments for the purpose you describe.
>
>
> At 06:18 PM 4/21/2014, you wrote:
>
> Hello Friends!
> Anyone have a lead for* NEMA 4x* stainless load centers (electrical
> panel)? Â Looking for 4 circuit version rated at about 60-100A @ 240VAC.
>
>
> Would like to use it for rooftop combiner for 3 Enphase inverter output
> circuits.
> Thank you!!
>
> Sunny Regards,
> Kirpal Khalsa
> NABCEP Certified PV Installation Professional
> Renewable Energy Systems
> www.oregonsolarworks.com
> 541-218-0201
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org<http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches..org>
>
> List-Archive:
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org<http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches..org>
>
> List-Archive:
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
>
>
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org<http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches..org>
>
> List-Archive:
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
>
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive:
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
>
>
--
Chris Mason
NABCEP Certified Solar PV Installer™
Solar Design Engineer
Generac Generators Industrial technician
www.cometsolar.com <http://www.cometenergysystems.com>
264.235.5670
869.662.5670
Skype: netconcepts
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140423/7785d00f/attachment-0004.html>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image009.png
Type: image/png
Size: 130249 bytes
Desc: not available
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140423/7785d00f/attachment-0014.png>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image012.jpg
Type: image/jpeg
Size: 2415 bytes
Desc: not available
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140423/7785d00f/attachment-0021.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image011.jpg
Type: image/jpeg
Size: 2593 bytes
Desc: not available
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140423/7785d00f/attachment-0022.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image013.jpg
Type: image/jpeg
Size: 2759 bytes
Desc: not available
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140423/7785d00f/attachment-0023.jpg>
-------------- next part --------------
A non-text attachment was scrubbed...
Name: image010.png
Type: image/png
Size: 24285 bytes
Desc: not available
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140423/7785d00f/attachment-0015.png>
More information about the RE-wrenches
mailing list