[RE-wrenches] Well pump relay question
Ray Walters
ray at solarray.com
Wed Apr 9 11:43:05 PDT 2014
I've had the contacts arc and not disconnect at 144 vdc. I used a
modified relay from an electric vehicle company: KTA services.
R.Ray Walters
CTO, Solarray, Inc
Nabcep Certified PV Installer,
Licensed Master Electrician
Solar Design Engineer
303 505-8760
On 4/4/2014 7:06 AM, Michael Morningstar wrote:
> I've done just that with DC rated 24VDC relays intended for marine and
> heavy equipment applications. No arcing while disconnecting SQFlexes
> under load.
>
> On Apr 3, 2014, at 11:06 PM, Allan Sindelar wrote:
>
>> Wrenches,
>> For my own off grid home, I would like to add four 60-cell modules as
>> a supplemental array, using a Midnite Classic charge controller. I
>> would like to set up a relay between this array and the controller to
>> allow me to direct the output to an SQFlex submersible well pump,
>> using a float switch to send the coil signal. The float switch in my
>> storage tank would send a call for water to the relay, which would
>> then allow array current to flow to the pump during daylight hours.
>> Once the tank is full, the relay switches, allowing array current to
>> flow to the Classic to charge my batteries. I have 24V battery DC
>> available in the well location as well.
>>
>> Would a standard open contact DPDT power relay with a 24V DC coil
>> work here? The contact terminals are rated for AC, not 125V DC. If I
>> connect the two sets of contacts in series, that would reduce but not
>> eliminate arcing. Has anyone tried this?
>>
>> This seems like the simplest solution, but I'm open to other
>> suggestions as well.
>> Thanks, Allan
>> --
>>
>> *Allan Sindelar*
>> _Allan at positiveenergysolar.com_ <mailto:Allan at positiveenergysolar.com>
>> NABCEP Certified PV Installation Professional
>> NABCEP Certified Technical Sales Professional
>> New Mexico EE98J Journeyman Electrician
>> Founder (Retired), *Positive Energy, Inc.*
>>
>> A Certified B Corporation^TM
>> Santa Fe, New Mexico
>> *505 780-2738 cell*
>>
>>
>> _______________________________________________
>> List sponsored by Home Power magazine
>>
>> List Address: RE-wrenches at lists.re-wrenches.org
>> <mailto:RE-wrenches at lists.re-wrenches.org>
>>
>> Change email address & settings:
>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>>
>> List-Archive:
>> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>>
>> List rules & etiquette:
>> www.re-wrenches.org/etiquette.htm
>>
>> Check out participant bios:
>> www.members.re-wrenches.org
>>
>
>
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20140409/104ff17a/attachment-0004.html>
More information about the RE-wrenches
mailing list