[RE-wrenches] DR>FX Compatibility Problem, Magnum inverters
Larry Crutcher, Starlight Solar
larry at starlightsolar.com
Fri Jun 19 20:11:09 PDT 2009
Yes. I thought of that so we turned on a few hundred watts. Same
problem. The Splindide power board is causing the issue. I tried RF
filtering, twisting inverter leads, EMI AC filter. Nothing would work.
It's really weird that a cheap import inverter would operate it.
Larry
On Jun 18, 2009, at 8:49 PM, jay peltz wrote:
> Hi Larry,
>
> Did this occur even if there were other loads on?
>
> jay
>
> peltz power
> On Jun 18, 2009, at 7:39 PM, Larry Crutcher, Starlight Solar wrote:
>
>> Hi Jeff,
>>
>> I am not sure if this relates to your issue but there is an issue
>> with Magnum inverters and Splindide washers. Splindide will not
>> work on a Magnum sine wave. They are aware of this. Here is a copy
>> of my old post to the list:
>>
>> ....I have a recent power issue come up with a Magnum inverter. A
>> customer tried to operate her Splindide washer/dryer but the motor
>> would not start. I looked at the waveform with a scope and RMS
>> voltage and frequency were fine. The waveform looked good until the
>> motor tried to start. The washer was putting a jagged noise riding
>> on the sine wave. The voltage and waveform still looked OK other
>> than the noise. I was mostly sure that this was the cause so I
>> grabbed a 600 watt cheap import sine wave inverter and connected
>> the washer. Same ripple was present on the waveform but the $400
>> inverter would run the washer motor fine. It also runs fine with a
>> 1600 watt Honda inverter/generator.
>>
>>
>> Larry Crutcher
>> Starlight Solar
>> (928) 941-1660
>> Renewable Energy Products, Service and Installation
>>
>> On Jun 18, 2009, at 4:44 PM, Jeff Oldham wrote:
>>
>>> Not sure if anyone offered this already - The DR will do a 5 sec.
>>> surge to 6200W the Outback will do a 5 sec. surge to 4800W. This
>>> is common, most mod's will surge considerable more than Sine's,
>>> that is the big trade off other than power quality and tare
>>> losses. In addition I'm very skeptical that the Staber only surges
>>> to 11A, have you measured the actual surge? When I replaced my
>>> good 'ol Trace 2512 (too many appliances disliked the mod. sine)
>>> and went to a Magnum 2812 my washer would kick it out as my washer
>>> surged to 31A and the Mag. would do 30! This is a modern Horz.
>>> axis machine. I now have the Magnum and a new Vanner ITC 12-3200W
>>> that does a 3 sec. surge to 6400W and will even run my wire welder
>>> and air compressor, both used to be genny only loads.
>>>
>>> -jeff o
>>>
>>>
>>> From the Solar, Wind and Hydro powered office of Jeff Oldham/
>>> Regenerative SOLutions
>>>
>>>
>>>
>>> ____________________________________________________________
>>> Save on Moving Supplies. Click Here!
>>> _______________________________________________
>>> List sponsored by Home Power magazine
>>>
>>> List Address: RE-wrenches at lists.re-wrenches.org
>>>
>>> Options & settings:
>>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>>>
>>> List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>>>
>>> List rules & etiquette:
>>> www.re-wrenches.org/etiquette.htm
>>>
>>> Check out participant bios:
>>> www.members.re-wrenches.org
>>>
>>
>> _______________________________________________
>> List sponsored by Home Power magazine
>>
>> List Address: RE-wrenches at lists.re-wrenches.org
>>
>> Options & settings:
>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>>
>> List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>>
>> List rules & etiquette:
>> www.re-wrenches.org/etiquette.htm
>>
>> Check out participant bios:
>> www.members.re-wrenches.org
>>
>
> _______________________________________________
> List sponsored by Home Power magazine
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Options & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out participant bios:
> www.members.re-wrenches.org
>
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20090619/b5e4af7d/attachment-0004.html>
More information about the RE-wrenches
mailing list