wind generator input [RE-wrenches]
Eric Andrews
eric at ecosolarnow.com
Thu Jun 12 14:44:10 PDT 2008
Thanks, that was my thoughts with the pinning, epoxy and the engineer.
Eric R. Andrews
NABCEP Certified PV Installer
Eco Solar, Inc.
www.ecosolarnow.com
PO Box 5194
Klamath Falls, OR 97601
541-281-8252
mailto:eric at ecosolarnow.com
Saving the World... One Solar Panel at a Time!
-----Original Message-----
From: Roger Dixon [mailto:roger.dixon at att.net]
Sent: Thursday, June 12, 2008 12:37 PM
To: eric at ecosolarnow.com
Cc: RE-wrenches at topica.com
Subject: RE: wind generator input [RE-wrenches]
Drill the rock and pin it in various places with rebar and epoxy them in
place. Cap the rock with a pad of appropriate size with rebar that is
attached to the pins in the rock. Welding the rebar to the pins would be my
preferred mode. Best to have an engineer spec what size rebar, pad, kind of
epoxy, etc., so the legal exposure is on him and not you. It will also give
you a solid installation.
Roger Dixon
-----Original Message-----
From: Eric Andrews [mailto:eric at ecosolarnow.com]
Sent: Thursday, June 12, 2008 3:27 PM
To: RE-wrenches at topica.com
Subject: wind generator input [RE-wrenches]
I am looking at my first wind job and looking at feedback on the SkyStream
3.7. For budget reasons, this will probably the pick. Customer has 12.4
mph avg. annual wind speed. The tower seems to be the tricky part, as the
soil type is rock. (Looking at guyed 70' by Southwest Windpower) Anyone
out there done a tower on rock soil type? I'm looking for experiences good
or bad.
Thanks all,
Eric R. Andrews
NABCEP Certified PV Installer
Klamath Falls, OR 97601
[Non-text portions of this message have been removed]
- - - -
Hosted by Home Power magazine
To send a message: RE-wrenches at topica.com
Archive of previous messages: http://lists.topica.com/lists/RE-wrenches/read
List rules & how to change your email address:
www.mrsharkey.com/wrenches/etiquette.php
Check out participant bios: www.mrsharkey.com/wrenches/
Moderator: michael.welch at homepower.com
- - - -
Hosted by Home Power magazine
To send a message: RE-wrenches at topica.com
Archive of previous messages: http://lists.topica.com/lists/RE-wrenches/read
List rules & how to change your email address:
www.mrsharkey.com/wrenches/etiquette.php
Check out participant bios: www.mrsharkey.com/wrenches/
Moderator: michael.welch at homepower.com
- - - -
Hosted by Home Power magazine
To send a message: RE-wrenches at topica.com
Archive of previous messages: http://lists.topica.com/lists/RE-wrenches/read
List rules & how to change your email address: www.mrsharkey.com/wrenches/etiquette.php
Check out participant bios: www.mrsharkey.com/wrenches/
Moderator: michael.welch at homepower.com
--^----------------------------------------------------------------
This email was sent to: michael.welch at re-wrenches.org
EASY UNSUBSCRIBE click here: http://topica.com/u/?bz8Qcs.bz9JC9.bWljaGFl
Or send an email to: RE-wrenches-unsubscribe at topica.com
For Topica's complete suite of email marketing solutions visit:
http://www.topica.com/?p=TEXFOOTER
--^----------------------------------------------------------------
More information about the RE-wrenches
mailing list