pole mount 150 watt modules [RE-wrenches]
Travis Creswell, Ozark Solar
ozsolar at ipa.net
Tue Feb 25 08:49:10 PST 2003
It does pay to check for used pipe. I recently bought two used ~18' pieces
of 8" Sch80 for $3/ft. New Sch40 8' was running $15/ft and I would have had
to buy an 21' pieces. Worked out perfect because I needed 8' under grade
and 10' above.
Speaking of array mounting pipes... Is anyone concerned about the long term
using standard pipe? I've looked around a little for galvanized stuff but
all I could find was custom order and big bucks. It's probably in the scrap
yard all the time but never when I am looking for it. I take the time and
clean the pipe very well and use the "rust" zinc primer type paint before I
set the pipe. Then, if time allows, I touch up the scratches that will be
under grade before I pour the concrete. After I'm done I come along with a
high quality oil base paint and paint the pole.
Travis Creswell
Ozark Energy Services
----- Original Message -----
From: "Tom Simko" <tom at skylinesolar.com>
To: <RE-wrenches at topica.com>
Sent: Tuesday, February 25, 2003 9:12 AM
Subject: Re: pole mount 150 watt modules [RE-wrenches]
> Basic welding and pipefitting skills could have saved some bucks, 2
> lengths of pipe would have done the whole project, with just 6' of
"scrap".
> The savings in pipe would have more then paid for hiring a guy with the
> needed skills. Strength on a properly welded pipe joint is not an issue.
> Also, when working with larger O.D. pipe check at any local steel
scrapyards
> for huge savings over buying new. My own pole mount is 24" O.D. 40' wide
and
> 20' high, and the steel cost 50 bucks at a scrap yard.
>
> Tom Simko
> Skyline Solar
>
> on 2/24/03 12:19 PM, Nick Nicholas, APS at APS at SBCGLOBAL.NET wrote:
>
> > Hi Keith:
> > We installed four 8" poles last month, and will install the arrays as
> > part of an SEA workshop in a few weeks. We used a torch to cut the pipe
to
> > 12', so each pole was not excessively heavy. It did take 3 guys and a
winch
> > to erect the poles. By the way, I have four 9' scrap pieces of the 8"
steel
> > pipes.
> > Alternative Power Systems
> > www.alternativepowersystems.com
> > aps at sbcglobal.net
> > 135 Colfax Ave.
> > Grass Valley, CA 95945
> > (530) 274-0588 phone
> > (530) 274-0589 fax
> > ----- Original Message -----
> > From: "Jay Peltz, Peltz Power" <jay at asis.com>
> > To: <RE-wrenches at topica.com>
> > Sent: Thursday, February 20, 2003 7:07 AM
> > Subject: Re: pole mount 150 watt modules [RE-wrenches]
> >
> >
> >> HI Keith,
> >>
> >> I just installed a 8 panel shell 150's. 6" pole. You'd better have a
> > bunch
> >> of strong guys to move that 8" pole.
> >>
> >> jay
> >>
> >> peltz power
> >>
> >> - - - -
> >> To send a message: RE-wrenches at topica.com
> >>
> >> Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
> >>
> >> List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
> >>
> >> Check out participant bios: www.mrsharkey.com/wrenches/index.html
> >>
> >> Hosted by Home Power magazine
> >>
> >> Moderator: michael.welch at homepower.com
> >>
> >
> > - - - -
> > To send a message: RE-wrenches at topica.com
> >
> > Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
> >
> > List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
> >
> > Check out participant bios: www.mrsharkey.com/wrenches/index.html
> >
> > Hosted by Home Power magazine
> >
> > Moderator: michael.welch at homepower.com
> >
> >
>
> - - - -
> To send a message: RE-wrenches at topica.com
>
> Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
>
> List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
>
> Check out participant bios: www.mrsharkey.com/wrenches/index.html
>
> Hosted by Home Power magazine
>
> Moderator: michael.welch at homepower.com
>
>
>
- - - -
To send a message: RE-wrenches at topica.com
Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
Check out participant bios: www.mrsharkey.com/wrenches/index.html
Hosted by Home Power magazine
Moderator: michael.welch at homepower.com
==^================================================================
This email was sent to: michael_welch at sbcglobal.net
EASY UNSUBSCRIBE click here: http://topica.com/u/?bz8Qcs.bz9JC9.bWljaGFl
Or send an email to: RE-wrenches-unsubscribe at topica.com
TOPICA - Start your own email discussion group. FREE!
http://www.topica.com/partner/tag02/create/index2.html
==^================================================================
More information about the RE-wrenches
mailing list