Module grounding revisited [RE-wrenches]

[Max Balchowsky]

I'd love to see composite frames. I think the down side would be the ones we
would install here in the desert. Have you seen what long term exposure to
sun and heat does to fiberglass?? I'd welcome something other that metal
that would stand the test of time in the desert heat....

Max

----- Original Message -----
From: "matthew tritt" <solarone at charter.net>
To: <RE-wrenches at topica.com>
Sent: Sunday, November 03, 2002 9:04 PM
Subject: Re: Module grounding revisited [RE-wrenches]


> Max, et all,
>
> The logical way to build module frames is not with aluminum, but with a
> non-metallic composite, such as carbon/fiberglass pultrusion. This is
vastly
> stronger, lighter, more weather resistant and would not require any kind
of
> grounding, as there would be no possibility of conductivity through the
> frame. The mounting structure could also use composite mounting rails for
> the same reasons. Then this whole f----ing issue would be moot.
>
> Tell me why I'm wrong Steve and Bill, you champions of the dominant
> paradigm!
>
> Matt
> ----- Original Message -----
> From: "Max Balchowsky" <max at seesolar.com>
> To: <RE-wrenches at topica.com>
> Sent: Sunday, November 03, 2002 7:04 PM
> Subject: Re: Module grounding revisited [RE-wrenches]
>
>
> > Jerry, the AstroPower Manuel I have tells me to ground the Module frames
> to
> > the Rails and the rail ground runs back to the main panel ground. It
also
> > specifys that the grounding must be done so that if a panel is removed
> from
> > the string the others must remain grounded.(layin lug) It does say that
> the
> > lug can be mounted so that the ground wire can be accessible after
module
> is
> > mounted against the roof.(drill into module frame?????). I've always
> > wondered what module manufacturers were thinking (or were they) when
they
> > put the ground screw hole near the middle of the module.......
> >
> > Max
> >
> > SEE Systems
> > 100 S. Sunrise Wy
> > Palm Springs, Ca. 92262
> > 760-403-6810
> >
> > ----- Original Message -----
> > From: "Jerry Caldwell" <solarcowboy at yahoo.com>
> > To: <RE-wrenches at topica.com>
> > Sent: Saturday, November 02, 2002 4:32 PM
> > Subject: Re: Module grounding revisited [RE-wrenches]
> >
> >
> > > We often ground the rack only.  Some of the ASE
> > > modules we use have a thick coat of paint on the
> > > frames, in which case we use the grounding disks
> > > provided by ASE to ground the individual modules.
> > >
> > > Astropower includes Professional Solar Products
> > > aluminum mounting rails in thier packaged kits and the
> > > Astropower installation manual says that only
> > > grounding the rails is necessary.  I'm not sure, but
> > > they might even have gotten the assembly listed as
> > > such.
> > >
> > > Jerry Caldwell
> > > Light Energy Systems
> > >
> > > ,
> > > > wrmiller at slonet.org writes:
> > > >
> > > >
> > > > > Therefore, if one grounds a rack frame, the
> > > > modules being "secured to and
> > > > > in electrical contact with" the racks renders the
> > > > module frames
> > > > > "effectively grounded".
> > > > >
> > > > > Comments?
> > > > >
> > > >
> > > > William,  My own on going test - experiment has been
> > > > to rely on the frames
> > > > getting grounded by the rack. I too think the
> > > > individual ground wire strung
> > > > panel to panel is stupid and a waste of time.
> > > > Supporting this hypothesis is
> > > > 100% ground continuity to every module frame and the
> > > > main rack. I have tested
> > > > every installation for ground over many years and
> > > > never had an ungrounded
> > > > frame. And I have gone back to old jobs and checked
> > > > years later. Still good
> > > > continuity.
> > > >
> > > > I think the language you found clearly gives the
> > > > option to ground the rack.
> > > >
> > > > Don
> > >
> > >
> > > __________________________________________________
> > > Do you Yahoo!?
> > > HotJobs - Search new jobs daily now
> > > http://hotjobs.yahoo.com/
> > >
> > > - - - -
> > > To send a message: RE-wrenches at topica.com
> > >
> > > Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
> > >
> > > List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
> > >
> > > Check out participant bios: www.mrsharkey.com/wrenches/index.html
> > >
> > > Hosted by Home Power magazine
> > >
> > > Moderator: michael.welch at homepower.com
> > >
> > >
> >
> > - - - -
> > To send a message: RE-wrenches at topica.com
> >
> > Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
> >
> > List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
> >
> > Check out participant bios: www.mrsharkey.com/wrenches/index.html
> >
> > Hosted by Home Power magazine
> >
> > Moderator: michael.welch at homepower.com
> >
> >
> >
>
> - - - -
> To send a message: RE-wrenches at topica.com
>
> Archive of previous messages: http://www.topica.com/lists/RE-wrenches/
>
> List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm
>
> Check out participant bios: www.mrsharkey.com/wrenches/index.html
>
> Hosted by Home Power magazine
>
> Moderator: michael.welch at homepower.com
>
>
>

- - - -
To send a message: RE-wrenches at topica.com

Archive of previous messages: http://www.topica.com/lists/RE-wrenches/

List rules & etiquette: http://www.mrsharkey.com/wrenches/etiquete.htm

Check out participant bios: www.mrsharkey.com/wrenches/index.html

Hosted by Home Power magazine

Moderator: michael.welch at homepower.com

==^================================================================
This email was sent to: michael.welch at homepower.com

EASY UNSUBSCRIBE click here: http://topica.com/u/?bz8Qcs.bz9JC9.bWljaGFl
Or send an email to: RE-wrenches-unsubscribe at topica.com

T O P I C A -- Register now to manage your mail!
http://www.topica.com/partner/tag02/register
==^================================================================