Trace wish list [RE-wrenches]
Drake Chamberlin, Quicksilver Electrical
solar at eagle-access.net
Tue Jan 16 19:43:24 PST 2001
How about 350 MCM lugs in the DC disconnect to ease installing the finely
stranded battery cable.
Jim Hartley wrote:
> Michael Welch, Home Power wrote:
> > Of all you wrenches, I got only 2 comments on my list, which now reads
> > as below. Surely my gathering of your requests has not been THAT good or
> > complete.
> >
> > 1. Silent sell.
> >
> > 2. EPROM back up battery
> >
> > 3. More wiring space both DC & AC.
> >
> > 4. Hold one of these input sessions at the MREA fair at Amherst.
> >
> > 5. The option of getting a bigger transfer switch built in. That 60
> > amp switch feels obsolete when so many houses are 100 amp service. (It
> > should not be added as an option if it will drive up the price of the
> > standard units.)
> >
> > 6. #2 wire terminals would be great for battery based grid intertie
> > systems.
> >
> > 7. DC Disconnect box redesign with three 2" or 2 1/2" KOs in the
> > bottom, or failing that, stay with the same box if they gotta, but move
> > the KO from the right side to the middle.
> >
> > 8. 2" knockouts are so tight that they will barely accept a
> > standard 2" PVC male adapter.
> >
> > 9. Trace DC disconnect should have room comparable to (or bigger
> > than) any standard 200 amp disconnect switch.
> >
> > 10. DC disconnect is too expensive, requires so much assembly and
> > has a yoke (to hold the breaker) with razor sharp edges.
> >
> > 11. Make corrections to the manual that more accurately reflect what
> > the unit actually does.
> >
> > 12. Adjustable time delay on the AUX relays and their hysteresis.
> >
> > 13. Buttons point/scroll in the correct direction.
> >
> > 14. Make the DC volt meters higher resolution so that we can set the
> > SW setpoints closer to the C-40 setpoints. (More power in grid tie with
> > higher voltage setpoints.)
> >
> > 15. Make ALL AC, relay, and plug in (except temp sensor) locations
> > front accessible.
> >
> > 16. Put temp sensor plug in on DC side where DC conduit to batteries
> > ends up.
> >
> > 17. More accurate/finer resolution metering (especially on AC amps)
> >
> > 18. Finer resolution/lower available value for search watts. (16
> > watts? Gimmie a break!)
> >
> > 19. Equalize battery feature that works, and at the touch of a
> > button on the faceplate.
> >
> > 20. Five year warranty.
> >
> > 21. Display of battery temp compensation/actual battery temperature
> > via temp comp probe.
> >
> > 22. A user programmable timer to allow the SW to return to float
> > mode after an AC 1 (and/or 2) input power interruption. There are
> > frequent power fluctuations in my system (mostly from switching
> > transients in the 130 VDC PV array) that knock the SW out of tolerance,
> > and it drops off the grid, only to return after 90 seconds ***and begins
> > another BULK charge cycle***. This feature would allow the user to force
> > the inverter to ignore power interruptions of a pre-set maximum duration
> > in ?? minute increments, allowing the inverter to return directly to a
> > FLOAT mode.
> >
> > 23. User programmable override of the 90 second time-out on "AC 1
> > (and/or2) in Good". (Actually, this is already available for AC 2. But
> > could be refined to include times when the inverter disconnects the
> > generator momentarily because of out of spec volts and/or Hz.)
> >
> > 24. Ability to start and/or stop generator by internal clock.
> >
> > 25. Better generator start options and/or another relay for the glow
> > plugs
> >
> > 26. Repair generator exercise bug. If you set the exercise period
> > for 7 days, the generator starts acting wacky, like starting and then
> > running until manually shut off.
> >
> > 27. Make cursor more visible. (How about a black square with the
> > letter/selection printed in reverse/background grey?)
> >
> > 28. A spare hardware kit, including 20 - Trace C40 Face Plate
> > Screws, 20 - SWCB Screws, 4 - DC Terminal nuts and star locks, 2 - RED
> > DC Terminal Covers (are DR and SW's the same?- I rarely install them,
> > inside SWCB or DRCB), 2 - Black DC Terminal Covers, & 1 - "Tester" Size
> > Bottle of Trace White touch up paint.
> >
> >
> > Michael Welch
>
> Oh, my. Could this be an entirely new inverter we're talking about?
>
> Jim Hartley
> http://www.homestead-specialties.com
> Business Email: JamesHartley at homestead-specialties.com
> Direct Email: grail at inil.com
>
> - - - - - - -
> To send a message:
> RE-wrenches at topica.com
>
> The archive of previous messages:
> http://www.topica.com/lists/RE-wrenches/
>
> To unsubscribe send a message to:
> RE-wrenches-unsubscribe at topica.com
>
> To check out the other RE-Wrench participants:
> www.mrsharkey.com/wrenches/index.html
>
> Hosted by Home Power magazine:
> www.homepower.com
>
> For info contact list moderator by email:
> michael.welch at homepower.com
>
> ____________________________________________________________
> T O P I C A -- Learn More. Surf Less.
> Newsletters, Tips and Discussions on Topics You Choose.
> http://www.topica.com/partner/tag01
- - - - - - -
To send a message:
RE-wrenches at topica.com
The archive of previous messages:
http://www.topica.com/lists/RE-wrenches/
To unsubscribe send a message to:
RE-wrenches-unsubscribe at topica.com
To check out the other RE-Wrench participants:
www.mrsharkey.com/wrenches/index.html
Hosted by Home Power magazine:
www.homepower.com
For info contact list moderator by email:
michael.welch at homepower.com
____________________________________________________________
T O P I C A -- Learn More. Surf Less.
Newsletters, Tips and Discussions on Topics You Choose.
http://www.topica.com/partner/tag01
More information about the RE-wrenches
mailing list