Trace wish list [RE-wrenches]
Jim Hartley
grail at inil.com
Tue Jan 16 12:37:56 PST 2001
Michael Welch, Home Power wrote:
> Of all you wrenches, I got only 2 comments on my list, which now reads
> as below. Surely my gathering of your requests has not been THAT good or
> complete.
>
> 1. Silent sell.
>
> 2. EPROM back up battery
>
> 3. More wiring space both DC & AC.
>
> 4. Hold one of these input sessions at the MREA fair at Amherst.
>
> 5. The option of getting a bigger transfer switch built in. That 60
> amp switch feels obsolete when so many houses are 100 amp service. (It
> should not be added as an option if it will drive up the price of the
> standard units.)
>
> 6. #2 wire terminals would be great for battery based grid intertie
> systems.
>
> 7. DC Disconnect box redesign with three 2" or 2 1/2" KOs in the
> bottom, or failing that, stay with the same box if they gotta, but move
> the KO from the right side to the middle.
>
> 8. 2" knockouts are so tight that they will barely accept a
> standard 2" PVC male adapter.
>
> 9. Trace DC disconnect should have room comparable to (or bigger
> than) any standard 200 amp disconnect switch.
>
> 10. DC disconnect is too expensive, requires so much assembly and
> has a yoke (to hold the breaker) with razor sharp edges.
>
> 11. Make corrections to the manual that more accurately reflect what
> the unit actually does.
>
> 12. Adjustable time delay on the AUX relays and their hysteresis.
>
> 13. Buttons point/scroll in the correct direction.
>
> 14. Make the DC volt meters higher resolution so that we can set the
> SW setpoints closer to the C-40 setpoints. (More power in grid tie with
> higher voltage setpoints.)
>
> 15. Make ALL AC, relay, and plug in (except temp sensor) locations
> front accessible.
>
> 16. Put temp sensor plug in on DC side where DC conduit to batteries
> ends up.
>
> 17. More accurate/finer resolution metering (especially on AC amps)
>
> 18. Finer resolution/lower available value for search watts. (16
> watts? Gimmie a break!)
>
> 19. Equalize battery feature that works, and at the touch of a
> button on the faceplate.
>
> 20. Five year warranty.
>
> 21. Display of battery temp compensation/actual battery temperature
> via temp comp probe.
>
> 22. A user programmable timer to allow the SW to return to float
> mode after an AC 1 (and/or 2) input power interruption. There are
> frequent power fluctuations in my system (mostly from switching
> transients in the 130 VDC PV array) that knock the SW out of tolerance,
> and it drops off the grid, only to return after 90 seconds ***and begins
> another BULK charge cycle***. This feature would allow the user to force
> the inverter to ignore power interruptions of a pre-set maximum duration
> in ?? minute increments, allowing the inverter to return directly to a
> FLOAT mode.
>
> 23. User programmable override of the 90 second time-out on "AC 1
> (and/or2) in Good". (Actually, this is already available for AC 2. But
> could be refined to include times when the inverter disconnects the
> generator momentarily because of out of spec volts and/or Hz.)
>
> 24. Ability to start and/or stop generator by internal clock.
>
> 25. Better generator start options and/or another relay for the glow
> plugs
>
> 26. Repair generator exercise bug. If you set the exercise period
> for 7 days, the generator starts acting wacky, like starting and then
> running until manually shut off.
>
> 27. Make cursor more visible. (How about a black square with the
> letter/selection printed in reverse/background grey?)
>
> 28. A spare hardware kit, including 20 - Trace C40 Face Plate
> Screws, 20 - SWCB Screws, 4 - DC Terminal nuts and star locks, 2 - RED
> DC Terminal Covers (are DR and SW's the same?- I rarely install them,
> inside SWCB or DRCB), 2 - Black DC Terminal Covers, & 1 - "Tester" Size
> Bottle of Trace White touch up paint.
>
>
> Michael Welch
Oh, my. Could this be an entirely new inverter we're talking about?
Jim Hartley
http://www.homestead-specialties.com
Business Email: JamesHartley at homestead-specialties.com
Direct Email: grail at inil.com
- - - - - - -
To send a message:
RE-wrenches at topica.com
The archive of previous messages:
http://www.topica.com/lists/RE-wrenches/
To unsubscribe send a message to:
RE-wrenches-unsubscribe at topica.com
To check out the other RE-Wrench participants:
www.mrsharkey.com/wrenches/index.html
Hosted by Home Power magazine:
www.homepower.com
For info contact list moderator by email:
michael.welch at homepower.com
____________________________________________________________
T O P I C A -- Learn More. Surf Less.
Newsletters, Tips and Discussions on Topics You Choose.
http://www.topica.com/partner/tag01
More information about the RE-wrenches
mailing list