[RE-wrenches] Honda 3000i low ac output

[RE Ellison]

I use the HarborFreight inverter generators and have had no problem at all with any of the magnums charging from them

Can’t say about the Honda but there’s something strange there obviously

Bob

> On Sep 4, 2021, at 2:39 PM, Dan Fink <danbob88 at gmail.com> wrote:
> 
> John; I have dealt with similar issues off-grid with the Honda 3000i "cubes," one client is in northern BC Canada and the 2 sites are only accessible by helicopter and float plane. So taking them to a local Honda PE shop is an expensive proposition!
> 
> Before replacing the (super expensive) inverter, try these steps:
> Unplug all the (numerous) white Molex wire connectors inside one at a time, clean the contacts with a wire brush, treat with anti-ox and replug.
> Check all those wire harnesses for chafing and worn-through insulation.
> Open the inverter, and check the wiring inside the aluminum case for chafing against the case. I believe this is a common failure area.
> If those don't help, get the 3000i shop manual, it has a very thorough troubleshooting section, and:
> There's an internal 6-pin plug under the throttle control where you can read the stator voltage, rotor voltage, etc. 
> Hopefully it's something simple!
> 
> The one Honda 3000i problem I was never able to solve was Magnum MMS inverters not accepting the AC input from the 3000i. We had similar systems at 2 camps, and tried both inverters with both generators (had to swap via heli of course) and it ended up as Magnum saying it's Honda's problem, and Honda saying it's Magnum's problem.
> 
> Good luck!
> 
> Dan Fink
> Owner, Buckville Energy Consulting LLC
> IREC Certified Instructor for PV and Small Wind Installation
> NABCEP Certified PV System Inspector
> NABCEP PV Associate
> danbob88 at gmail.com
> 970-672-4342
> 
>  
> 
> 
>> On Sat, Sep 4, 2021 at 8:41 AM John Blittersdorf <john.blittersdorf at gmail.com> wrote:
>> I have a Honda 3000i for my off grid system that shows 84 vac output.  I suspect that the inverter is failing.  Just checking to see if any of you have seen this failure mode?
>> 
>> John Blittersdorf
>> _______________________________________________
>> List sponsored by Redwood Alliance
>> 
>> Pay optional member dues here: http://re-wrenches.org
>> 
>> List Address: RE-wrenches at lists.re-wrenches.org
>> 
>> Change listserver email address & settings:
>> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>> 
>> There are two list archives for searching. When one doesn't work, try the other:
>> https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
>> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>> 
>> List rules & etiquette:
>> http://www.re-wrenches.org/etiquette.htm
>> 
>> Check out or update participant bios:
>> http://www.members.re-wrenches.org
>> 
> _______________________________________________
> List sponsored by Redwood Alliance
> 
> Pay optional member dues here: http://re-wrenches.org
> 
> List Address: RE-wrenches at lists.re-wrenches.org
> 
> Change listserver email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
> 
> There are two list archives for searching. When one doesn't work, try the other:
> https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/
> http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
> 
> List rules & etiquette:
> http://www.re-wrenches.org/etiquette.htm
> 
> Check out or update participant bios:
> http://www.members.re-wrenches.org
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches_lists.re-wrenches.org/attachments/20210907/fddc129a/attachment.htm>