[RE-wrenches] Looking for insulated #6 bare standoff

[Dana]

Ray,
In Idaho if it does not have UL attached it is not acceptable. Personally I think this would be just fine & a step up maybe with a WEEB top & bottom involved.

----------------------------------------------------------------------------
Dana Orzel                              Great Solar Works, Inc. 
C - 208.721.7003                       dana at solarwork.com
Idaho Contractor - # 028765         Idaho PV # 028374
NABCEP # 051112-136                       www.solarwork.biz
"Responsible Technologies for Responsible People since 1988"  
 Please consider the environment before printing this email.


-----Original Message-----
From: RE-wrenches <re-wrenches-bounces at lists.re-wrenches.org> On Behalf Of Ray
Sent: Thursday, April 19, 2018 5:05 PM
To: re-wrenches at lists.re-wrenches.org
Subject: Re: [RE-wrenches] Looking for insulated #6 bare standoff

On tracking arrays,  I have had both solid and stranded copper ground wire strain harden and break.  The cyclical motion will slowly work away at coarse cables. I've even seen solid #6 break off on just a tilt adjustable array. I now use a braided ground strap at least for the rack to pole ground connection.  This is the same strap that is used to ground generators and other moving electrical equipment.

https://www.delcity.net/store/Ground-Straps/p_818655.h_818654

I isolate it at the connection to the aluminum with a sandwich of Stainless fender washers and a 1/4" bolt with toothed lock washer to bite into the AL, or it also works well folded in ground Lugs and buss bars. You can open up the weave of the braided copper in the middle to get the 1/4" bolt through.  I've checked these years later: no corrosion, wire not broken off at the connector.

Ray


On 4/19/18 3:48 PM, Dana wrote:
> The bare #8 is an EGC for #10 USE PV wire on the tracker to the array mounted combiner box.
>
> ----------------------------------------------------------------------------
> Dana Orzel                              Great Solar Works, Inc.
> C - 208.721.7003                       dana at solarwork.com
> Idaho Contractor - # 028765         Idaho PV # 028374
> NABCEP # 051112-136                       www.solarwork.biz
> "Responsible Technologies for Responsible People since 1988"
>  Please consider the environment before printing this email.
>
>
> -----Original Message-----
> From: RE-wrenches <re-wrenches-bounces at lists.re-wrenches.org> On 
> Behalf Of Hilton Dier
> Sent: Thursday, April 19, 2018 3:39 PM
> To: re-wrenches at lists.re-wrenches.org
> Subject: [RE-wrenches] Looking for insulated #6 bare standoff
>
> Would #8 meet code? I thought that exposed ground wire had to be #6 minimum.
>
> Hilton Dier III
> Renewable Energy Design
> Missisquoi River Hydro LLC
> _______________________________________________
> List sponsored by Redwood Alliance
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change listserver email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive: 
> http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist
> .html
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out or update participant bios:
> www.members.re-wrenches.org
>
> _______________________________________________
> List sponsored by Redwood Alliance
>
> List Address: RE-wrenches at lists.re-wrenches.org
>
> Change listserver email address & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
> List-Archive: 
> http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist
> .html
>
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
>
> Check out or update participant bios:
> www.members.re-wrenches.org
>

_______________________________________________
List sponsored by Redwood Alliance

List Address: RE-wrenches at lists.re-wrenches.org

Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out or update participant bios:
www.members.re-wrenches.org