<div dir="auto">Well with the BPE 16kWh cabinet is not an issue then when its u der a Outback radian there is just enough room for a note pad. When we did the industrial batteries l will say that would be awkward hence they were never under the inverter mainly for the safety and gassing, blue planets dont gas.<div dir="auto">Jerry</div><div dir="auto">NAPCEP PV inspector</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sun, Jan 31, 2021, 10:28 PM Ray <<a href="mailto:ray@solarray.com">ray@solarray.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div>
<p>This isn't just a Li+ issue, this has been a problem going all
the way back to the 90s. Basically many AHJs don't catch it, but
its still a violation. We either keep the battery cabinet
shallow, or we put the battery cabinet to the side. Just use
some common sense, if you are having to lean awkwardly over or
around something to get to the breakers, its probably a
violation. <br>
</p>
<pre cols="72">Ray Walters
Remote Solar
303 505-8760</pre>
<div>On 1/31/21 5:55 PM, Jason Szumlanski
wrote:<br>
</div>
<blockquote type="cite">
<div dir="auto">I'm reading that the working space must be down to
the floor/grade with the exception of other equipment extending
up to 6 inches deeper than the enclosure for which the working
space applies.
<div dir="auto"><br>
</div>
<div dir="auto">For example, technically you can't put a 32 inch
deep base cabinet and countertop below a load center. I see it
all the time, but inspectors around here in some jurisdictions
will not allow it. </div>
<div dir="auto"><br>
</div>
<div dir="auto">I seriously doubt I would be flagged for a 24
inch deep battery enclosure below a 12 inch deep inverter with
integrated disconnects, but by the book it seems like a
violation. </div>
<div dir="auto"><br>
</div>
<div dir="auto">Jason</div>
<div dir="auto"><br>
</div>
</div>
<br>
<div class="gmail_quote">
<div dir="ltr" class="gmail_attr">On Sun, Jan 31, 2021, 5:38 PM
Jerry Shafer <<a href="mailto:jerrysgarage01@gmail.com" target="_blank" rel="noreferrer">jerrysgarage01@gmail.com</a>>
wrote:<br>
</div>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div dir="auto"> <span style="font-family:sans-serif"> l
dont know that this NEC code applies in the way you are
reading or understanding it, I do see where foreign
components are restricted with in the space. We</span> have
systems with two or three outback radians above blueplanet
batteries and have not seen an issue. The BPE's are in an
enclosed cabinet fire approved and protected from shock,
putting batteries further away will create space issues.
Since all of these components are required for the "system"
to operate they are necessary.
<div dir="auto">Jerry</div>
</div>
<br>
<div class="gmail_quote">
<div dir="ltr" class="gmail_attr">On Sun, Jan 31, 2021,
12:28 PM Jason Szumlanski <<a href="mailto:jason@floridasolardesigngroup.com" rel="noreferrer noreferrer" target="_blank">jason@floridasolardesigngroup.com</a>>
wrote:<br>
</div>
<blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div dir="ltr">
<div class="gmail_default" style="font-family:arial,helvetica,sans-serif">I'm
seeing a lot of pictures of LiPO battery systems and
people are mounting equipment above them like load
centers, inverters with disconnects, and other
serviceable enclosures. Some of these battery systems
are 24 inches deep or more. This seems to violate NEC
110.26 requirements for the other serviceable
equipment, but the pictures are proudly displayed as
models of success. Even slender Tesla Powerwalls stick
out significantly when stacked 2 or 3 deep and would
be more than 6 inches deeper than a standard load
center. Sure, the battery cabinets make great places
to rest tools while working, but does anyone else see
this as problematic? </div>
<div class="gmail_default" style="font-family:arial,helvetica,sans-serif"><br>
</div>
<div class="gmail_default" style="font-family:arial,helvetica,sans-serif">Jason
Szumlanski</div>
<div class="gmail_default" style="font-family:arial,helvetica,sans-serif">Florida
Solar Design Group </div>
<img alt="" style="display:flex" src="https://mailtrack.io/trace/mail/bdd06583d462e3938bb1d19f5a2b8d4e4bf8dda6.png?u=1613865" width="0" height="0"></div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer noreferrer noreferrer" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one
doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer noreferrer noreferrer noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer noreferrer noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer noreferrer noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote>
</div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer noreferrer" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't
work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer noreferrer noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer
noreferrer noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote>
</div>
<br>
<fieldset></fieldset>
<pre>_______________________________________________
List sponsored by Redwood Alliance
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank" rel="noreferrer">RE-wrenches@lists.re-wrenches.org</a>
Change listserver email address & settings:
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank" rel="noreferrer">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a>
There are two list archives for searching. When one doesn't work, try the other:
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" target="_blank" rel="noreferrer">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank" rel="noreferrer">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a>
List rules & etiquette:
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank" rel="noreferrer">http://www.re-wrenches.org/etiquette.htm</a>
Check out or update participant bios:
<a href="http://www.members.re-wrenches.org" target="_blank" rel="noreferrer">http://www.members.re-wrenches.org</a>
</pre>
</blockquote>
</div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank" rel="noreferrer">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div>