<html>
<head>
<meta http-equiv="Content-Type" content="text/html; charset=UTF-8">
</head>
<body>
<p>That's the whole point: we need the LBCO to be higher than 48v to
catch the beginning of that steep drop off, so that there is still
enough reserve left to keep the monitoring and solar charge
controllers in operation, and avoid the dreaded dark start. With
Simpliphi, we don't have the dark start, but it still requires
manual reset. This isn't theoretical, we have been having
serious trouble with a system because of Schneider's inability to
set the LVD above 48 v. Also setting the voltage higher (lower
DOD) extends the cycle life of these batteries. Otherwise, I love
the stable 51 volts of Li+, even under load. <br>
</p>
<pre class="moz-signature" cols="72">Ray Walters
Remote Solar
303 505-8760</pre>
<div class="moz-cite-prefix">On 3/22/20 4:15 PM, Jerry Shafer wrote:<br>
</div>
<blockquote type="cite"
cite="mid:CAMUFgmXxjRX1rXZ86RhRJjawhuoD0pO1uf0h7v-1Em_T92F_2g@mail.gmail.com">
<meta http-equiv="content-type" content="text/html; charset=UTF-8">
<div dir="auto">Wrenches
<div dir="auto">Don't let the LBCU scare you as this battery has
such a flat SOC line that when it falls off there is not much
left in the tank. In addition set the flex net to low SOC at
15% and critical to 10%.</div>
</div>
<br>
<div class="gmail_quote">
<div dir="ltr" class="gmail_attr">On Sun, Mar 22, 2020, 12:15 PM
Sindelar Solar <<a href="mailto:Allan@sindelarsolar.com"
target="_blank" rel="noreferrer" moz-do-not-send="true">Allan@sindelarsolar.com</a>>
wrote:<br>
</div>
<blockquote class="gmail_quote" style="margin:0 0 0
.8ex;border-left:1px #ccc solid;padding-left:1ex">
<div text="#000000" bgcolor="#FFFFFF">
<p>Specifically with Blue Ion, the installation manual
recommends 48V as LBCO, but also recommends setting it a
bit higher:</p>
<p>"Recommended Low Voltage Disconnect Setting: 48 VDC
(~2-10% State of Charge)<br>
BMU will power down the Blue Ion 2.0 cabinet at 44 VDC
(<1% State of Charge)<br>
Based on system discharge patterns, SoC and voltage
correlations will vary.<br>
We recommend you err on the side of caution with a higher
LVD setting and adjust as necessary.<br>
To prevent a dark start event, we recommend leaving a
little reserve \u201cfuel in the tank\u201d."</p>
<p>I have used 48VDC with success, and had one system indeed
shut down at 44V, leaving 1% left to reboot.<br>
</p>
<p>Allan<br>
</p>
<div>On 3/22/2020 12:44 PM, Ray wrote:<br>
</div>
<blockquote type="cite">
<p>Blue Ion, and Simpliphi that I know of.<br>
</p>
<pre cols="72">Ray Walters
Remote Solar
303 505-8760</pre>
<div>On 3/21/20 2:48 PM, Dave Angelini Offgrid Solar
wrote:<br>
</div>
<blockquote type="cite">
<p>I see what you mean Ray. Sorry I misread your mail.
There are not too many batteries out there that need
LBCO above 48V. Which ones are you talking about
please?</p>
<p><strong><span style="font-size:small">Dave Angelini
Offgrid Solar</span></strong></p>
<div>
<pre><strong><span style="font-size:small">"we go where powerlines don't"
<a href="http://members.sti.net/offgridsolar/" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">http://members.sti.net/offgridsolar/</a>
e-mail <a href="mailto:offgridsolar@sti.net" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">offgridsolar@sti.net</a>
text 209 813 0060</span></strong></pre>
</div>
<p>On Sat, 21 Mar 2020 11:18:21 -0700, Dave Angelini
Offgrid Solar <a href="mailto:offgridsolar@sti.net"
rel="noreferrer noreferrer" target="_blank"
moz-do-not-send="true"><offgridsolar@sti.net></a>
wrote:</p>
<blockquote type="cite"
style="padding-left:5px;border-left:#1010ff 2px
solid;margin-left:5px;width:100%">
<p>Hi Ray,</p>
<p>Which XW? There are 3 now. The old graybox XW
defaults at 44V LBCO and the range is 40 to 48V.
There also was firmware back in its day that got
older units updated. Schneider still has the
firmware under discontinued products.</p>
<p>XW+ is default 44V and adjustable 36 to 44 vdc.</p>
<p>XW pro is running downstairs and I will take a
look. It would be my guess that it is the same as
XW+. I think one needs to be sure they are in
Advanced settings to tweak LBCO also.</p>
<p>I am not plugging Schneider and have done work for
both Outback and Schneider as well as my clients.
Hope this helps. </p>
<div>
<pre><strong><span style="font-size:small">Dave Angelini Offgrid Solar
"we go where powerlines don't"
<a href="http://members.sti.net/offgridsolar/" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">http://members.sti.net/offgridsolar/</a>
e-mail <a href="mailto:offgridsolar@sti.net" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">offgridsolar@sti.net</a>
text 209 813 0060</span></strong></pre>
</div>
<p>On Sat, 21 Mar 2020 11:46:21 -0400, Ray <a
href="mailto:ray@solarray.com" rel="noreferrer
noreferrer" target="_blank" moz-do-not-send="true"><ray@solarray.com></a>
wrote:</p>
<blockquote
style="padding-left:5px;border-left:#1010ff 2px
solid;margin-left:5px;width:100%">
<p>We've been having good luck with SImpliphi, the
pricing has recently gotten much more
competitive. As it's names states, its simple.
Each 3.8 kWh unit has an 80 amp breaker built into
the top, weigh about 75 lbs, and are a bit smaller
than an L16 but with carry handles. We use an
insulated 2 pole combiner block to run all the
parallel conductors to the main 2/0 cable. No
monitoring, but they do have an handy setup guide
with recommended settings, specific for each
manufacturer (including Outback). </p>
<p>Note to all: Schneider XW can still not set its
LVD above 48, which basically makes it
incompatible with most Li+ batteries. Their tech
support has been abysmal as well. We're looking
forward to them as one of the larger companies in
the business, to put additional resources into
their engineering, and come out with at least a
firmware update to correct this problem. </p>
<pre>Ray Walters
Remote Solar
303 505-8760</pre>
<div>On 3/20/20 3:59 PM, David Katz wrote:</div>
<blockquote
style="padding-left:5px;border-left:#1010ff 2px
solid;margin-left:5px;width:100%">
<div dir="ltr">
<div class="gmail_default"
style="font-family:arial,sans-serif">Hello
Wrenches,</div>
<div class="gmail_default"
style="font-family:arial,sans-serif">I am
working with some people that want to use a 20
kw-hour to 30 kw-hour 48 volt lithium-ion
battery with an Outback Radian and Outback FM
charge controllers.</div>
<div class="gmail_default"
style="font-family:arial,sans-serif">They are
considering using Discover, Blue-Ion, Battle
Born or SimpliPhi batteries.</div>
<div class="gmail_default"
style="font-family:arial,sans-serif">Does any
one have any recommendations of which battery
functions best with the Outback system.</div>
<div class="gmail_default"
style="font-family:arial,sans-serif">Thanks,</div>
<div class="gmail_default"
style="font-family:arial,sans-serif">David
Katz</div>
</div>
<br>
<fieldset></fieldset>
<pre>_______________________________________________
List sponsored by Redwood Alliance
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">RE-wrenches@lists.re-wrenches.org</a>
Change listserver email address & settings:
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a>
List-Archive: <a href="http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html</a>
List rules & etiquette:
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">www.re-wrenches.org/etiquette.htm</a>
Check out or update participant bios:
<a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">www.members.re-wrenches.org</a>
</pre>
</blockquote>
</blockquote>
</blockquote>
<br>
<fieldset></fieldset>
<pre>_______________________________________________
List sponsored by Redwood Alliance
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">RE-wrenches@lists.re-wrenches.org</a>
Change listserver email address & settings:
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a>
List-Archive: <a href="http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html</a>
List rules & etiquette:
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">www.re-wrenches.org/etiquette.htm</a>
Check out or update participant bios:
<a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">www.members.re-wrenches.org</a>
</pre>
</blockquote>
<br>
<fieldset></fieldset>
<pre>_______________________________________________
List sponsored by Redwood Alliance
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">RE-wrenches@lists.re-wrenches.org</a>
Change listserver email address & settings:
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a>
List-Archive: <a href="http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html</a>
List rules & etiquette:
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">www.re-wrenches.org/etiquette.htm</a>
Check out or update participant bios:
<a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer" target="_blank" moz-do-not-send="true">www.members.re-wrenches.org</a>
</pre>
</blockquote>
<div>-- <br>
<div>
<p class="MsoNormal" style="line-height:normal"><b><span>Allan
Sindelar</span></b><span><br>
</span><a href="mailto:allan@sindelarsolar.com"
rel="noreferrer noreferrer" target="_blank"
moz-do-not-send="true"><span>allan@sindelarsolar.com</span></a><span><br>
</span><span>NABCEP Certified PV Installation
Professional<br>
New Mexico EE98J Journeyman Electrician<br>
Founder (Retired), <span>Positive Energy, Inc<span>.</span></span><br>
<b>505 780-2738 cell</b></span><span></span></p>
<p class="MsoNormal"> </p>
</div>
</div>
</div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
List Address: <a
href="mailto:RE-wrenches@lists.re-wrenches.org"
rel="noreferrer noreferrer" target="_blank"
moz-do-not-send="true">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a
href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org"
rel="noreferrer noreferrer noreferrer" target="_blank"
moz-do-not-send="true">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a
href="http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html"
rel="noreferrer noreferrer noreferrer" target="_blank"
moz-do-not-send="true">http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm"
rel="noreferrer noreferrer noreferrer" target="_blank"
moz-do-not-send="true">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer
noreferrer noreferrer" target="_blank"
moz-do-not-send="true">www.members.re-wrenches.org</a><br>
<br>
</blockquote>
</div>
<br>
<fieldset class="mimeAttachmentHeader"></fieldset>
<pre class="moz-quote-pre" wrap="">_______________________________________________
List sponsored by Redwood Alliance
List Address: <a class="moz-txt-link-abbreviated" href="mailto:RE-wrenches@lists.re-wrenches.org">RE-wrenches@lists.re-wrenches.org</a>
Change listserver email address & settings:
<a class="moz-txt-link-freetext" href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a>
List-Archive: <a class="moz-txt-link-freetext" href="http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html">http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html</a>
List rules & etiquette:
<a class="moz-txt-link-abbreviated" href="http://www.re-wrenches.org/etiquette.htm">www.re-wrenches.org/etiquette.htm</a>
Check out or update participant bios:
<a class="moz-txt-link-abbreviated" href="http://www.members.re-wrenches.org">www.members.re-wrenches.org</a>
</pre>
</blockquote>
</body>
</html>