<font face="arial" size="3"><p style="margin:0;padding:0;">VMP not VOC</p>
<p style="margin:0;padding:0;"> </p>
<p style="margin:0;padding:0;">todd</p>
<p style="margin:0;padding:0;"> </p>
<p style="margin:0;padding:0;"> </p>
<p style="margin:0;padding:0;"> </p>
<p style="margin:0;padding:0;">On Thursday, October 24, 2013 1:26pm, "jay peltz" <jay@asis.com> said:<br /><br /></p>
<div id="SafeStyles1382662297">
<p style="margin:0;padding:0;">> Hi Jeffe,<br />> <br />> I don't know the specs on those Kyocera, but if they are the same VOC then they<br />> are fine together.<br />> <br />> As to a enclosure for the CC's, I'd look at Midnight.<br />> They have about a million different boxes, you'll find one that will do the job<br />> for you I'm sure.<br />> <br />> Depending on the area, you might look at a midnight 150v, or 200v or 250v<br />> controller, as you can then run all in series.<br />> <br />> jay<br />> <br />> peltz power<br />> <br />> <br />> On Oct 24, 2013, at 1:13 PM, Jesse Dahl wrote:<br />> <br />> > Hello,<br />> ><br />> > Looked at a system today that consisted of the following:<br />> ><br />> > 15 - Kyocera 158W modules<br />> > 3 - Kyocera 185W modules<br />> > 1 - Outback MX60<br />> > 8 - New Trojan L16RE (48V system)<br />> > 1 - Xantrex SW Plus<br />> ><br />> > 6 months ago he swapped out his old charge controller to the new MX60 and<br />> purchased the new batteries at that time. The array wiring did not change and is<br />> wired in 6 strings of 3. (confusing to the MX60?)<br />> ><br />> > He is now adding 4 Kyocera 240W modules. He also purchased another MX60 for<br />> this array.<br />> ><br />> > From my perspective, removing the 3 185W modules and getting them on their<br />> own controller would be a better use of the modules. The system currently does<br />> not have any disconnects on the PV side. There are fuses in the combiner boxes on<br />> the array, but no disconnects inside at the charge controller. So adding 3 charge<br />> controllers, and now needing to add GFDI, means a box of some kind needs to be<br />> added to house these breakers.<br />> ><br />> > Outbacks GFPs and panel mount breakers will work, but what is the best<br />> mounting solution for these? One DC Flexware enclosure? It will of course allow<br />> for all the DC OCPD and allow for the landing of the output of the charge<br />> controllers. Or is there another enclosure/OCPD solution I should look at?<br />> ><br />> ><br />> > Thanks as always!<br />> ><br />> > Jesse<br />> ><br />> ><br />> ><br />> ><br />> ><br />> <br />> _______________________________________________<br />> List sponsored by Home Power magazine<br />> <br />> List Address: RE-wrenches@lists.re-wrenches.org<br />> <br />> Change email address & settings:<br />> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org<br />> <br />> List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org<br />> <br />> List rules & etiquette:<br />> www.re-wrenches.org/etiquette.htm<br />> <br />> Check out participant bios:<br />> www.members.re-wrenches.org<br />> <br />></p>
</div></font><br><br><br>Sent from Finest Planet WebMail.<br>