<div dir="auto"><div>I backed the absorb voltage down to 56.4V from 57.6V. today the batteries reached the desired absorb voltage, dropped down, jumped around a small amount for about 10 minutes, and then settled around 55.5V (even though the desired float voltage is set to 53.4V). But it's stable now. </div><div dir="auto"><br></div><div dir="auto">I don't understand why the float setpoint isn't being respected, but I didn't have that erratic behavior today, and the BMSs are just fine. </div><div dir="auto"><br></div><div dir="auto">The voltages reported by the three AIOs have always been a couple of tenths off from highest to lowest. </div><div dir="auto"><br></div><div dir="auto">Maybe yesterday was just a weird anomaly, but I do think the battery BMSs did see spikes above 60V and shut down for protection. That's the only thing I can think of. I'm continuing to monitor and will report back with and findings. </div><div><br></div><div data-smartmail="gmail_signature"><div dir="ltr"><br>Jason Szumlanski<div><span style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px">Principal Solar Designer | Florida Solar Design Group</span><br style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px"><span style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px">NABCEP Certified Solar Professional (PVIP)</span><br style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px"><span style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px">Florida State Certified Solar Contractor CVC56956</span></div><div><font color="#333333" face="Roboto, RobotoDraft, Helvetica, Arial, sans-serif">Florida Certified Electrical Contractor EC13013208</font></div></div></div></div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Sat, Jan 24, 2026, 5:52 PM Jason Szumlanski <<a href="mailto:jason@floridasolardesigngroup.com">jason@floridasolardesigngroup.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="auto"><div><div>I imagine the readings are being taken at slightly different intervals. The sampling is 10 seconds for Solar Assistant.</div><div dir="auto"><br></div><div dir="auto">Speaking of absorb, I noticed that there is an absorb and float setting for the Midnite AIO, but no absorb time setting. These batteries have never dropped to float. They just sit at absorb voltage once it's reached each day. I can't figure out how to get them to drop to float, but there hasn't been any adverse effects until now.  </div><div><br></div><div data-smartmail="gmail_signature"><div dir="ltr"><br>Jason Szumlanski<div><span style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px">Principal Solar Designer | Florida Solar Design Group</span><br style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px"><span style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px">NABCEP Certified Solar Professional (PVIP)</span><br style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px"><span style="color:rgb(51,51,51);font-family:Roboto,RobotoDraft,Helvetica,Arial,sans-serif;font-size:13px">Florida State Certified Solar Contractor CVC56956</span></div><div><font color="#333333" face="Roboto, RobotoDraft, Helvetica, Arial, sans-serif">Florida Certified Electrical Contractor EC13013208</font></div></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Sat, Jan 24, 2026, 5:22 PM Jay <<a href="mailto:jay.peltz@gmail.com" target="_blank" rel="noreferrer">jay.peltz@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="auto"><div dir="ltr"></div><div dir="ltr">I don’t understand how 3 inverters on a single buss could be recording such wildly different dc voltage readings. Regardless if the inverters are independent or paralleled. </div><div dir="ltr"><br></div><div dir="ltr">I don’t have those battereis specs but would expect absorb if there is any to be less than 90 minutes? </div><div dir="ltr">Or did the issue occur at the exact end of absorb?</div><div dir="ltr"><br></div><div dir="ltr">What a pain. </div><div dir="ltr"><br></div><div dir="ltr">Jay</div><div dir="ltr"><br></div><div dir="ltr"><br></div><div dir="ltr"><br><blockquote type="cite">On Jan 24, 2026, at 1:36 PM, Jason Szumlanski via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" rel="noreferrer noreferrer" target="_blank">re-wrenches@lists.re-wrenches.org</a>> wrote:<br><br></blockquote></div><blockquote type="cite"><div dir="ltr"><div dir="ltr"><div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif">I have a triple stack of off-grid Midnite AIO connected to a 60 kWh lithionics battery bank (51.2V LFP) in open loop. Today the site had BMS shutdowns (there are two BMSs, one for each 30 kWh stack of batteries). Both BMSs shut down about 90 minutes after the solar got the batteries to 100% and were just meeting loads with solar.</div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif"><br></div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif">I got some data from Solar Assistant (attached) that shows erratic voltage readings from each of the three inverters. This has never happened at this site before. Some of the voltage readings exceeded 60V, which I am guessing caused one or both BMS to shut off and come back on, possibly quickly. </div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif"><br></div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif">I do see some solar charging spikes, so it looks like the inverters would detect a low battery state and start charging, raising the voltage of the batteries quickly, and the process repeating itself.</div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif"><br></div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif">Any ideas on what the source of the problem might be?</div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif"><br></div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif">Thanks,</div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif"><br></div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif">Jason Szumlanski </div><div class="gmail_default" style="font-family:arial,helvetica,sans-serif">Florida Solar Design Group</div><br clear="all"></div><div><br></div><div><br></div><div><div dir="ltr" class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><b><div style="text-align:center"></div></b></div></div></div></div></div></div></div></div></div>
<div><Image 1149.jpg></div><div><Image 1148.jpg></div><div><Image 1151.jpg></div><div><Image 1150.jpg></div><span>_______________________________________________</span><br><span>List sponsored by Redwood Alliance</span><br><span></span><br><span>Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://re-wrenches.org</a></span><br><span></span><br><span>List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer noreferrer" target="_blank">RE-wrenches@lists.re-wrenches.org</a></span><br><span></span><br><span>Change listserver email address & settings:</span><br><span><a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a></span><br><span></span><br><span>There are two list archives for searching. When one doesn't work, try the other:</span><br><span><a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a></span><br><span><a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a></span><br><span></span><br><span>List rules & etiquette:</span><br><span><a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a></span><br><span></span><br><span>Check out or update participant bios:</span><br><span><a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://www.members.re-wrenches.org</a></span><br><span></span><br></div></blockquote></div></blockquote></div></div></div>
</blockquote></div>