<div dir='auto'><div>I have had this experience as well with a couple of Schneider systems. The SCP doesn't seem to be the master when an Insight or gateway is on the Xanbus.</div><div dir="auto"><br></div><div dir="auto">Generator settings and charge controller settings have not stuck.</div><div><br></div><div data-smartmail="gmail_signature">-Glenn</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Jan 14, 2026 08:46, Jason Szumlanski via RE-wrenches <re-wrenches@lists.re-wrenches.org> wrote:<br type="attribution" /><blockquote class="quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div dir="ltr"><div><div style="font-family:'arial' , 'helvetica' , sans-serif">I updated the settings for all devices via InsightLocal and the settings are sticking now. I think there was some sort of conflict. When I changed settings via the SCP, they would not be reflected in InsightLocal, but when I changed settings in InsightLocal the settings would instantly change on the SCP.</div><div style="font-family:'arial' , 'helvetica' , sans-serif"><br /></div><div style="font-family:'arial' , 'helvetica' , sans-serif">I think the source of the high DC voltage issue was something else, however. I discovered that all of the charge controllers were set to Flooded rather than Custom battery type (for LFP), and some of the charge controllers had equalization enabled.</div><div style="font-family:'arial' , 'helvetica' , sans-serif"><br /></div><div style="font-family:'arial' , 'helvetica' , sans-serif">It was cloudy yesterday, so I have to wait until solar gets the batteries to 100%, hopefully today, to see if the high DC voltage issue comes back. </div><br clear="all" /></div><div><div dir="ltr"><div dir="ltr"><br />Jason Szumlanski<div><span style="color:rgb( 51 , 51 , 51 );font-family:'roboto' , 'robotodraft' , 'helvetica' , 'arial' , sans-serif;font-size:13px">Principal Solar Designer | Florida Solar Design Group</span><br style="color:rgb( 51 , 51 , 51 );font-family:'roboto' , 'robotodraft' , 'helvetica' , 'arial' , sans-serif;font-size:13px" /><span style="color:rgb( 51 , 51 , 51 );font-family:'roboto' , 'robotodraft' , 'helvetica' , 'arial' , sans-serif;font-size:13px">NABCEP Certified Solar Professional (PVIP)</span><br style="color:rgb( 51 , 51 , 51 );font-family:'roboto' , 'robotodraft' , 'helvetica' , 'arial' , sans-serif;font-size:13px" /><span style="color:rgb( 51 , 51 , 51 );font-family:'roboto' , 'robotodraft' , 'helvetica' , 'arial' , sans-serif;font-size:13px">Florida State Certified Solar Contractor CVC56956</span></div><div><font color="#333333" face="Roboto, RobotoDraft, Helvetica, Arial, sans-serif">Florida Certified Electrical Contractor EC13013208</font></div></div></div></div><br /></div><br /><div><div dir="ltr">On Tue, Jan 13, 2026 at 6:33 PM Dave Angelini Offgrid Solar via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org">re-wrenches@lists.re-wrenches.org</a>> wrote:<br /></div><blockquote style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb( 204 , 204 , 204 );padding-left:1ex"><div style="font-size:12pt;font-family:'verdana' , 'geneva' , sans-serif">
<p>A guess is too many devices on the xanbus. Are you using Facility?  The -60 reverting is a new one for me. Maybe isolate each one seperately in case one is malo.</p>
<p>buenas suerte!</p>
<div><br />
<pre> </pre>
<pre><strong><span style="font-size:small">Dave Angelini Offgrid Solar
"we go where powerlines don't"
<a href="http://members.sti.net/offgridsolar/">  </a><a style="color:blue;font-size:11px;font-family:'lucida grande' , 'verdana' , 'arial' , 'helvetica' , sans-serif;font-weight:400;background-color:rgb( 255 , 255 , 255 )" href="https://offgridsolar1.com/"><span style="font-size:12pt">https://offgridsolar1.com/</span></a><a href="http://members.sti.net/offgridsolar/"> </a>
e-mail  <a href="mailto:offgridsolar@sti.net">offgridsolar@sti.net</a>
text 209 813 0060</span></strong></pre>
</div>
<p><br /></p>
<p>On 2026-01-13 4:29 am, Jason Szumlanski via RE-wrenches wrote:</p>
<blockquote style="padding:0px 0.4em;border-left:2px solid rgb( 16 , 16 , 255 );margin:0px">
<div>
<div dir="auto">
<div>I have a new client with an existing Schneider dual XW Pro system with four MPPT 100 and two MPPT 60 charge controllers. They have a SCP, AGS, and Insight. </div>
<div dir="auto"> </div>
<div dir="auto">The system is reporting DC over voltage faults on the two inverters (viewable via SCP. The battery voltage is not high. It's a bank of EG4 LL batteries that would hit their high battery cutoff well before the XW detects a high battery condition.</div>
<div dir="auto"> </div>
<div dir="auto">I went through all of the setting and discovered that the two MPPT 60 were set to a nominal voltage of 36V. I fixed that by changing them to 48V and cleared the faults and all was well. I did this though the SCP.</div>
<div dir="auto"> </div>
<div dir="auto">By the time I came home, however, the faults returned and the MPPT 60 both reverted to 36V nominal. </div>
<div dir="auto"> </div>
<div dir="auto">I'm not sure why the DC over voltage faults are showing up on the XWs, but it seems related to the nominal voltage issue on the MPPT 60s.</div>
<div dir="auto"> </div>
<div dir="auto">Any ideas?</div>
<div dir="auto"> </div>
<div dir="auto">Schneider tech support has me wasting time today going for a boat ride to the site to put a meter on the battery terminals, when I know it's obviously not an actual battery voltage issue. I'm hoping to steer them in a different direction. </div>
<div dir="auto"> </div>
<div dir="auto"> </div>
<div dir="auto">Jason Szumlanski </div>
<div dir="auto">Florida Solar Design Group </div>
<div dir="auto"> </div>
<div>
<div dir="ltr">
<div dir="ltr">
<div dir="ltr">
<div dir="ltr">
<div dir="ltr">
<div dir="ltr">
<div style="text-align:center"> </div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
</div>
<br />
<div style="margin:0px;padding:0px;font-family:monospace">_______________________________________________<br />List sponsored by Redwood Alliance<br /><br />Pay optional member dues here: <a href="http://re-wrenches.org">http://re-wrenches.org</a><br /><br />List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org">RE-wrenches@lists.re-wrenches.org</a><br /><br />Change listserver email address & settings:<br /><a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br /><br />There are two list archives for searching. When one doesn't work, try the other:<br /><a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br /><a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br /><br />List rules & etiquette:<br /><a href="http://www.re-wrenches.org/etiquette.htm">http://www.re-wrenches.org/etiquette.htm</a><br /><br />Check out or update participant bios:<br /><a href="http://www.members.re-wrenches.org">http://www.members.re-wrenches.org</a><br /><br /></div>
</blockquote>
</div>
_______________________________________________<br />
List sponsored by Redwood Alliance<br />
<br />
Pay optional member dues here: <a href="http://re-wrenches.org">http://re-wrenches.org</a><br />
<br />
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org">RE-wrenches@lists.re-wrenches.org</a><br />
<br />
Change listserver email address & settings:<br />
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br />
<br />
There are two list archives for searching. When one doesn't work, try the other:<br />
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br />
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br />
<br />
List rules & etiquette:<br />
<a href="http://www.re-wrenches.org/etiquette.htm">http://www.re-wrenches.org/etiquette.htm</a><br />
<br />
Check out or update participant bios:<br />
<a href="http://www.members.re-wrenches.org">http://www.members.re-wrenches.org</a><br />
<br />
</blockquote></div></div>
</blockquote></div><br></div>