<div dir="auto"><div>Kirk, if the batteries are in closed loop, the SOC is being reported by the battery BMS. In open loop, my understanding is the SOC is usually less accurate as it is calculated by the inverter based on our programming settings. </div><div dir="auto">The SOC calculation in closed loop is based on much more data  (collected by the BMS), but also depends on the level of sophistication of that firmware. The assumed SOC can get significantly out of whack with the actual, especially if they are top balanced with some regularity.  What that frequency of required top balancing varies from product to product. </div><div dir="auto">The inverter calculated SOC (open loop) is generally less accurate and probably requires more regular top balancing than closed loop, to remain within a reasonable estimate of the actual SOC.</div><div dir="auto">Howie<br><br><div class="gmail_quote gmail_quote_container" dir="auto"><div dir="ltr" class="gmail_attr">On Tue, Jul 15, 2025, 9:24 PM Kirk Herander via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="ltr"><div dir="ltr">Generally speaking, with these respective AIO inverters, where is the supposed SOC being calculated from and how often is that source manually or auto calibrated?<div><br></div><div>I only have experience in AIOs with Fortress inverters and their evault batteries. I had a situation where the house went dark when closed-loop SOC read 35%.</div><div><br></div><div>Some may remember from this forum, Fortress confirmed battery volts had to go above 55v to auto recalibrate. It was a Vermont mid-winter and the customer never turned on the genny because he thought the bats were safely at 35%., Actually they were close to 0% due to the lack of winter recalibration.</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Jul 15, 2025 at 8:56 PM Lou Russo via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank" rel="noreferrer">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="ltr"><div>We definitely experience that. Mostly with Sol-Ark and Homegrid. Generator even starts but it is not quick enough to do anything. Have the client power cycle and everything is fine. Had this happen last week, batteries were at 79%. <br clear="all"></div><div><br></div><div><div dir="ltr" class="gmail_signature"><div dir="ltr"><div dir="ltr">Aloha,<div>Lou Russo </div><div>Spree Solar Systems LLC </div><div>C-34322</div><div><br></div></div></div></div></div><br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Jul 15, 2025 at 1:44 PM Howie Michaelson via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank" rel="noreferrer">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto">These are useful suggestions for how to deal with low battery conditions, however I understand Jason's situation to be a hardware or firmware issue - the inverter temporarily reads battery voltage or SOC as 0% and shuts off, needing manual intervention to turn back on.  I'm not sure if i am having the same issue on at least a couple of sites with an AIO and 1 or 2 PF16s in closed loop, by I've seen the inverters without warning seemingly loose the batteries (which are in a relatively high SOC  - 70-80%), see no SOC, then shut itself off.  So far the client has gotten the inverter back to on by shutting it down entirely and restarting it.  It fires back up and operates fine as though nothing has happened.  Anyone else experiencing that? <div dir="auto">Howie</div><div dir="auto">Sun Catcher </div></div><br></blockquote></div></blockquote></div></div><br>
</blockquote></div></div></div>