<div><div><div><div dir="auto">Jason,</div><div dir="auto"><br></div><div dir="auto">This is a great question. I was waiting for responses, because I’ve thought this as well.</div><div dir="auto"><br></div><div dir="auto">Typically I have sized load conductors to either Sol Ark output or gen output, depending on which was higher, but you are absolutely right that with grid assist programmed, this number could be higher. Either OCPD or internal settings could work to avoid upsizing conductors to meet potential combined amapacity of gen + inverter. However, I’m not crystal clear on how those settings work for Sol Ark. I know there was a discussion a few weeks back where Jharen from Sol Ark said it’s possible to derate AC input/output, but it sounded like the conversation went off line. </div><div dir="auto"><br></div><div dir="auto">Any insight would be appreciated. </div><div dir="auto"><br></div><div dir="auto">Best,</div><div dir="auto"><br></div><div dir="auto">Chris </div></div></div></div><div><div><div><div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Jun 13, 2025 at 7:36 AM Jason Szumlanski via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-style:solid;padding-left:1ex;border-left-color:rgb(204,204,204)"><div dir="auto"><div>I think there was a previous thread on this, but I can't seem to find it. </div><div dir="auto"><br></div><div dir="auto">I'm wondering how everyone is handling wire sizing on inverter output circuits for off-grid systems when there is a generator on the grid input. Let's use the Sol-Ark 15K as an example. </div><div dir="auto"><br></div><div dir="auto">Without a generator, it's pretty simple. 80 amp over current protection with #4 copper minimum. </div><div dir="auto"><br></div><div dir="auto">With a 20 kW generator that has 80A rated current and 100A overcurrent protection, the entire generator current can pass through, so now we are talking about a minimum of #3 copper. But is that really the case? Since the inverter can be programmed to do grid assist, is it necessary to size the conductors for 180A?</div><div dir="auto"><br></div><div dir="auto">It gets trickier in parallel installations. If you have two inverters and the same generator, in theory the generator input and output is split evenly between the two inverters, so do you size the output conductors for 80A inverter output, 130A for inverter plus half of the generator, or do you still need to assume 180A? </div><div dir="auto"><br></div><div dir="auto">Assuming the conductors are the same length from the generator to the load, in theory the generator pass through should be equal on each inverter, but is that really the case? How do we know how each inverter will use the generator input and pass through current, especially in a grid assist scenario?</div><div dir="auto"><br></div><div dir="auto">I have been erring on the side of caution and simply using 200A conductors on the output side of both single and parallel inverter installations. The inverter output wire cost, complexity, and difficulty is high. </div><div dir="auto"><br></div><div dir="auto">The inverter manufacturers have not made it clear in their documentation how grid pass through and grid assist works. </div><div dir="auto"><br></div><div dir="auto">This is one of the reasons that I have started specifying the Midnite AIO. With a 100A load breaker, the output load conductor requirement is #2 copper per the manual. I assume it is not specified as #3 because it is a 100% continuous duty breaker. Regardless, #2 saves a lot of cost and is way easier to work with than 3/0 copper. </div><div dir="auto"><br></div><div dir="auto">I am getting ready to specify a parallel EG4 Flexboss21 system using the GridBoss to combine them and do load shedding. This seems to be another good alternative where the inverter output circuit only needs to be 90A rated. The GridBoss can accept a 125A generator breaker, eliminating the requirement for pass through all together. This seems like a pretty well thought out approach.</div><div dir="auto"><br></div><div dir="auto"><br></div><div dir="auto">Jason Szumlanski </div><div dir="auto">Florida Solar Design Group </div><div data-smartmail="gmail_signature"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><div dir="ltr"><b><div style="text-align:center"><table border="0" cellpadding="0" cellspacing="0" style="font-weight:400;text-align:start;font-family:"helvetica neue",helvetica,arial,sans-serif;color:rgb(34,34,34)"><tbody style="font-family:"helvetica neue",helvetica,arial,sans-serif"></tbody></table></div></b></div></div></div></div></div></div></div></div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div></div>
</div>
</div>
</div>