<div dir="ltr" gmail_original="1"><div><div class="gmail_default" style="font-family: arial, helvetica, sans-serif;">Question about the Power Distribution Blocks...</div><div class="gmail_default" style="font-family: arial, helvetica, sans-serif;"><br></div><div class="gmail_default" style="font-family: arial, helvetica, sans-serif;">I can't seem to find these with 4/0 main and four 4/0 taps. Does anyone have a source that is knowledgeable? The catalogs are not much help - too many parts, too confusing.</div><div class="gmail_default" style="font-family: arial, helvetica, sans-serif;"><br></div><div class="gmail_default" style="font-family: arial, helvetica, sans-serif;">Also, are PDBs all rated for fine-stranded cable like this? I know only some Polaris taps are. We normally use PDBs for parallel inverter AC in/out splicing, but I never considered them for battery bus connections. It seems that might work well when the ampacity requirement is modest to get a compact battery combiner.</div><br clear="all"></div><div><div dir="ltr" class="gmail_signature"><div dir="ltr"><br>Jason Szumlanski<div><span style="color: rgb(51, 51, 51); font-family: Roboto, RobotoDraft, Helvetica, Arial, sans-serif; font-size: 13px;">Principal Solar Designer | Florida Solar Design Group</span><br style="color: rgb(51, 51, 51); font-family: Roboto, RobotoDraft, Helvetica, Arial, sans-serif; font-size: 13px;"><span style="color: rgb(51, 51, 51); font-family: Roboto, RobotoDraft, Helvetica, Arial, sans-serif; font-size: 13px;">NABCEP Certified Solar Professional (PVIP)</span><br style="color: rgb(51, 51, 51); font-family: Roboto, RobotoDraft, Helvetica, Arial, sans-serif; font-size: 13px;"><span style="color: rgb(51, 51, 51); font-family: Roboto, RobotoDraft, Helvetica, Arial, sans-serif; font-size: 13px;">Florida State Certified Solar Contractor CVC56956</span></div><div><font color="#333333" face="Roboto, RobotoDraft, Helvetica, Arial, sans-serif">Florida Certified Electrical Contractor EC13013208</font></div></div></div></div><br></div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Thu, Jun 12, 2025 at 2:34 PM William Miller via RE-wrenches <re-wrenches@lists.re-wrenches.org> wrote:<br></div><blockquote class="gmail_quote" style="margin: 0px 0px 0px 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;"><div dir="auto">Indeed, the lack of wiring infrastructure is troubling. Attached is my first run at it. I am not satisfied. </div><div dir="auto"><br></div><div dir="auto">I bought some 6x6 gutter stock today. I will chop it into ~12” sections to set on top of each battery with an opening to the connections. I will post a photo afterwards. </div><div dir="auto"><br></div><div dir="auto">I am supposed to host a tour next week with some Deka staff. I will ask about the questions posed. I hope there is no hidden problems that make these batteries unsuitable. They seem solid  </div><div dir="auto"><br></div><div dir="auto"><br></div><div dir="auto"><div dir="auto"><img src="cid:d9c4bd6a-0dd4-4f34-93d6-97125a9f8526" style="max-width: 100%;" data-surl="cid:d9c4bd6a-0dd4-4f34-93d6-97125a9f8526"></div><br clear="all"><div dir="auto"><div dir="ltr" class="gmail_signature">Ps:  the photo cuts off the inverter but it is just out of frame at top. </div><div dir="ltr" class="gmail_signature"><br></div><div dir="ltr" class="gmail_signature">PPS:  I’m trying to not be amused at the Italian stereotype. We have an Italian surrogate son that is in the commercial solar industry in Italy. I will ask him about the cultural nuances. </div><div dir="ltr" class="gmail_signature"><br></div><div dir="ltr" class="gmail_signature"><br></div><div dir="ltr" class="gmail_signature">William Miller<br>Miller Solar.com<br>805-438-5600<br><a href="http://www.millersolar.com" target="_blank"><span id="mt-tracked-link_0_1749754804184" style="color: red;"></span>www.millersolar.com</a><br></div></div></div><div><br></div><div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Jun 10, 2025 at 8:18 PM Bradley Bassett via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank">re-wrenches@lists.re-<wbr>wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin: 0px 0px 0px 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;"><div dir="ltr">I've just heard that WM is using the Deka Duration batteries. At AEE we had a very good relationship with MK Battery and I brought in the Deka Duration to sell without really looking at all the potential issues first. However, I did become aware of them after looking at how to install them in detail. I'm curious how anyone does this with multiple batteries. I came up with lots of configurations trying to get around the extreme lack of wiring room in stacked batteries. I ended up doing drawings showing them stacked on their rear end on the floor 3 deep from the wall with a battery combiner on top of each 3 stack. Contact with tech support was always referred to the Italian company and every time I received a very condescending and arrogant response. Then I finally read the warranty in detail, unfortunately after selling some, and having to buy them back. Turns out that at that time (still?) the warranty excluded in entirety any system installed with an inverter that did not have closed loop comms with the battery. Also the temperature range to stay under warranty was basically room temperature only. After discovering all of these issues I decided that we would no longer carry them. I will say that I had no problem getting one to communicate with my XW+ inverter through the gateway CAN bus. The one that I ended up with has certainly worked fine, but of course is not under any warranty, and never has been since put into operation with an open communication inverter in a utility shed that gets down to 40°F.<div><br></div><div>Brad Bassett</div></div>
______________________________<wbr>_________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804186" style="color: red;"></span>http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.<wbr>org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804188" style="color: red;"></span>http://lists.re-wrenches.org/<wbr>options.cgi/re-wrenches-re-<wbr>wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804190" style="color: red;"></span>https://www.mail-archive.com/<wbr>re-wrenches@lists.re-wrenches.<wbr>org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804192" style="color: red;"></span>http://lists.re-wrenches.org/<wbr>pipermail/re-wrenches-re-<wbr>wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804193" style="color: red;"></span>http://www.re-wrenches.org/<wbr>etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804195" style="color: red;"></span>http://www.members.re-<wbr>wrenches.org</a><br>
<br>
</blockquote></div></div>
______________________________<wbr>_________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804197" style="color: red;"></span>http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.<wbr>org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804198" style="color: red;"></span>http://lists.re-wrenches.org/o<wbr>ptions.cgi/re-wrenches-re-wren<wbr>ches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804200" style="color: red;"></span>https://www.mail-archive.com/r<wbr>e-wrenches@lists.re-wrenches.o<wbr>rg/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804202" style="color: red;"></span>http://lists.re-wrenches.org/p<wbr>ipermail/re-wrenches-re-wrench<wbr>es.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804204" style="color: red;"></span>http://www.re-wrenches.org/eti<wbr>quette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer" target="_blank"><span id="mt-tracked-link_0_1749754804205" style="color: red;"></span>http://www.members.re-wrenches<wbr>.org</a><br>
<br>
</blockquote></div>