<div dir="auto">I’ve had good experience with installing a five or 10 second delay on one of the pumps. This way the pumps’ start-current spikes are staggered</div><div dir="auto"><br></div><div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Thu, May 8, 2025 at 12:38 PM Jason Szumlanski via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-style:solid;padding-left:1ex;border-left-color:rgb(204,204,204)"><div dir="auto"><div dir="auto">Water pump is not my strong suit. I usually leave that up to the experts around here. Unfortunately, the experts are clueless when it comes to off-grid living. I have a client with a setup that is pretty unworkable. I'm trying to give him some general guidance. </div><div dir="auto"><br></div><div dir="auto">The setup uses a brackish water (might as well be salt water) very shallow well. It is about 3 ft underground for the water table. The RO system installer has a 1 HP 1.25 SF Century centrifugal surface pump drawing water from the well and pressurizing the inlet of a StaRite 1.25 HP booster pump designed for about 10 GPM at 150 PSI to run water through the RO system. </div><div dir="auto"><br></div><div dir="auto">Both of the pumps run simultaneously and continuously when producing water, and the water production is ridiculously low. I understand that RO production is going to be slow, but the amount of power these pumps are using is pure insanity. I have advised the client that, at a minimum, this system needs to be on a smart load circuit to run only when there is adequate battery capacity. The startup surgery is not a concern, but it does flicker the lights and it makes quite the racket. </div><div dir="auto"><br></div><div dir="auto">My thoughts are that the well pump is drastically oversized. The booster pump only needs 10 gallons per minute, and it has a suction head of 15 ft. I don't even know if the well pump pressurizing the booster pump inlet is required. I'm thinking we should be slow pumping water into an interim holding tank at least at the height of the booster pump. At a minimum, the well pump should be on a pressure switch with pressure tank so it can cycle. </div><div dir="auto"><br></div><div dir="auto">Can anyone give me some general guidance, and perhaps a VFD pump that does not have the startup surge and is maybe more efficient? During times of heavy use, the RO system can easily eat up half of the PV produced during a day at this site.</div><div dir="auto"><br></div><div dir="auto"><br></div><div dir="auto">Jason Szumlanski </div><div dir="auto">Florida Solar Design Group </div></div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div></div>