<div dir="ltr">Jay, great questions. <div>One of the few good things about the OutBack Skybox (I think it was that one) was the lifting holes on the upper back corners so that a bar or pipe could be run through making it much easier for a lift into place. Maybe for the 300 lb batteries lifting eyes on all four top corners so that 2 bars across the front and back could be used by 4 people to lift would be good. Of course a mechanical lift will also do the job. I've always thought that a battery that sits on the floor would be preferable unless subject to flooding. </div><div>I've used different cable sizes and lengths to the extreme on my own system, and there is a slight difference in charge between batteries but it never gets too far out of balance. I do have one battery that gets slightly more cycling, but that is actually what I prefer in this instance. </div><div>Remember the Aquion battery with the #12 cables and Amphenol PV connectors?</div><div><br></div><div>Brad</div></div><br><div class="gmail_quote gmail_quote_container"><div dir="ltr" class="gmail_attr">On Mon, Feb 3, 2025 at 2:34 PM jay via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div>Hi All<div><br></div><div>Im wondering about a few things as we are talking batteries.</div><div><br></div><div>1. how do people feel about the amphenol battery connector vs lugs? A lot of batteries are going that way.  Lots to like about them. </div><div><br></div><div>2. battery cable lengths.  I see both things said, that they have to be the same length or doesn’t matter.  </div><div>I did a large fortress system that they wouldn’t warranty unless equal lengths.  Mind you, it would have added about 200’ of 4/0.  I convinced them by using different wire sizes to make the % VD the same and they agreed. </div><div><br></div><div>3. battery lifting attachment points.  300# is really heavy and is it actually more than 2 people can do via OSHA?</div><div>What about some threaded holes for lifting rings, or places for straps on the side?</div><div><br></div><div>Thanks</div><div><br></div><div>jay</div><div><br></div><div><br id="m_5008805402029781948lineBreakAtBeginningOfMessage"><div><br><blockquote type="cite"><div>On Feb 3, 2025, at 10:27 AM, Maverick Brown via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank">re-wrenches@lists.re-wrenches.org</a>> wrote:</div><br><div><div dir="auto">Bill<div><br></div><div>So far I have installed eight of the midnight power flow 16 batteries. </div><div><br></div><div>The most recent was three on an Outback Radian. </div><div><br></div><div>I documented that process here, even with settings. </div><div><br></div><div><div style="display:block"><div style="display:inline-block" role="link"><a style="border-radius:10px;font-family:-apple-system,Helvetica,Arial,sans-serif;display:block;width:300px;overflow:hidden;text-decoration:none" rel="nofollow" href="https://youtu.be/AwoaTZtHMjU?feature=shared" dir="ltr" role="button" width="300" target="_blank"><table style="table-layout:fixed;border-collapse:collapse;width:300px;background-color:rgb(35,35,31);font-family:-apple-system,Helvetica,Arial,sans-serif" cellpadding="0" cellspacing="0" border="0" width="300"><tbody><tr><td align="center"><img style="width: 300px; height: 168px;" width="300" height="168" alt="maxresdefault.jpg"></td></tr><tr><td><table bgcolor="#23231F" cellpadding="0" cellspacing="0" width="300" style="table-layout:fixed;font-family:-apple-system,Helvetica,Arial,sans-serif;background-color:rgb(35,35,31)"><tbody><tr><td style="padding:8px 0px"><div style="max-width:100%;margin:0px 16px;overflow:hidden"><div style="font-weight:700;font-size:12px;overflow:hidden;text-overflow:ellipsis;text-align:left"><a rel="nofollow" href="https://youtu.be/AwoaTZtHMjU?feature=shared" style="text-decoration:none" target="_blank"><font color="#FFFFFF" style="color:rgb(255,255,255)">Outback Radian GS8048A upgraded to MidNite Powerflo16 48kWh!</font></a></div><div style="font-weight:600;font-size:11px;overflow:hidden;text-overflow:ellipsis;text-align:left"><a rel="nofollow" href="https://youtu.be/AwoaTZtHMjU?feature=shared" style="text-decoration:none" target="_blank"><font color="#FFFFFF" style="color:rgba(235,235,245,0.6)">youtu.be</font></a></div></div></td></tr></tbody></table></td></tr></tbody></table></a></div></div><br></div><div><div dir="ltr"><br></div><div dir="ltr"> I also connected the Powerflo16 to XW system and the Polyon Tech compatibility shows the details of the BMS nicely. </div><div dir="ltr"><br></div><div dir="ltr">Documented here. </div><div dir="ltr"><br></div><div dir="ltr"><div style="display:block"><div style="display:inline-block" role="link"><a style="border-radius:10px;font-family:-apple-system,Helvetica,Arial,sans-serif;display:block;width:300px;overflow:hidden;text-decoration:none" rel="nofollow" href="https://youtu.be/bfWgmGNrIuE?feature=shared" dir="ltr" role="button" width="300" target="_blank"><table style="table-layout:fixed;border-collapse:collapse;width:300px;background-color:rgb(212,212,212);font-family:-apple-system,Helvetica,Arial,sans-serif" cellpadding="0" cellspacing="0" border="0" width="300"><tbody><tr><td align="center"><img style="width: 300px; height: 168px;" width="300" height="168" alt="maxresdefault.jpg"></td></tr><tr><td><table bgcolor="#D4D4D4" cellpadding="0" cellspacing="0" width="300" style="table-layout:fixed;font-family:-apple-system,Helvetica,Arial,sans-serif;background-color:rgb(212,212,212)"><tbody><tr><td style="padding:8px 0px"><div style="max-width:100%;margin:0px 16px;overflow:hidden"><div style="font-weight:700;font-size:12px;overflow:hidden;text-overflow:ellipsis;text-align:left"><a rel="nofollow" href="https://youtu.be/bfWgmGNrIuE?feature=shared" style="text-decoration:none" target="_blank"><font>Connecting the MidNite Powerflo16 to Schneider XW Series Inverters</font></a></div><div style="font-weight:600;font-size:11px;overflow:hidden;text-overflow:ellipsis;text-align:left"><a rel="nofollow" href="https://youtu.be/bfWgmGNrIuE?feature=shared" style="text-decoration:none" target="_blank"><font color="#A2A2A9" style="color:rgba(60,60,67,0.6)">youtu.be</font></a></div></div></td></tr></tbody></table></td></tr></tbody></table></a></div></div><br></div><div dir="ltr"><br></div><div dir="ltr">I have also made a chart of LiFePO4 settings and would like some feedback, if possible. I basically treat all 16s LiFePO4 batteries the same, Absorb at 3.45 per cell and everything trickles down from their. </div><div dir="ltr"><br></div><div dir="ltr"><img alt="Battery SOC State of Charge Map 2025-01-22.pdf"></div><div dir="ltr"><br></div><div dir="ltr"><div dir="ltr">Thank you,<div><br></div><div>Maverick</div><div><div style="font-family:Helvetica;font-size:12px"><div><br></div><div>Maverick Brown<br>Off-Grid Solar Commander since 2006<br>Maverick Solar Enterprises, Inc.<br> • Solar Commander Remote Power<br> • SunFlow Systems Cathodic Protection <br><a href="mailto:maverick@mavericksolar.com" target="_blank">maverick@mavericksolar.com</a><br>512-460-9825</div><div><br></div></div></div><div><br></div></div></div><div dir="ltr"><br><blockquote type="cite">On Feb 2, 2025, at 10:52 PM, Bill Battagin via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank">re-wrenches@lists.re-wrenches.org</a>> wrote:<br><br></blockquote></div><blockquote type="cite"><div dir="ltr"><span>Have any off-gridders done a system with Powerflo16's to power pre-LFP OB/FX inverters?  The FM80's LFP settings in this system are compatible with LFP but I'm looking for options other than using the Aux in the CC's wired to a NC relay and from there to the inverter on/off landings in the green terminal of the OB/FX for the LBCO and reconnect function.</span><br><span></span><br><span>            I've been down this road before, though a different equipment.  I've used the Aux from a Classic for inverter LBCO and reconnect though its never been fully "tested", although I read "open" and closed" at the un-wired aux landing when I forced it with a high LBCO setting.  Just thinking about the highest reliability.</span><br><span></span><br><span>        Thanks in advance.</span><br><span></span><br><span>Bill</span><br><span></span><br><span>Feather River Solar Electric</span><br><span>Bill Battagin, owner</span><br><span>4291 Nelson St. (Shipping)</span><br><span>5575 Genesee Rd. (USPS, UPS)</span><br><span>Taylorsville, CA  95983</span><br><span>530-284-7849, 258-1641(cell)</span><br><span>CA. C10 Lic # 874049</span><br><span>Solar Powered since 1982</span><br><span>Home of the Sunny Side Up</span><br><span></span><br><span></span><br><span>-- </span><br><span>This email has been checked for viruses by Avast antivirus software.</span><br><span><a href="http://www.avast.com" target="_blank">www.avast.com</a></span><br><span>_______________________________________________</span><br><span>List sponsored by Redwood Alliance</span><br><span></span><br><span>Pay optional member dues here: <a href="http://re-wrenches.org" target="_blank">http://re-wrenches.org</a></span><br><span></span><br><span>List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a></span><br><span></span><br><span>Change listserver email address & settings:</span><br><span><a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a></span><br><span></span><br><span>There are two list archives for searching. When one doesn't work, try the other:</span><br><span><a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a></span><br><span><a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a></span><br><span></span><br><span>List rules & etiquette:</span><br><span><a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">http://www.re-wrenches.org/etiquette.htm</a></span><br><span></span><br><span>Check out or update participant bios:</span><br><span><a href="http://www.members.re-wrenches.org" target="_blank">http://www.members.re-wrenches.org</a></span><br><span></span><br></div></blockquote></div></div><span id="m_5008805402029781948cid:3C19FCFF-5927-4B0F-A174-8F7931893114"><Battery SOC State of Charge Map 2025-01-22.pdf></span><span id="m_5008805402029781948cid:B4A1A587-99C0-48CF-AB61-D947B4F9CE08"><maxresdefault.jpg></span><span id="m_5008805402029781948cid:C15FB76B-A4C6-4C4E-A75E-A943452CE7D6"><maxresdefault.jpg></span>_______________________________________________<br>List sponsored by Redwood Alliance<br><br>Pay optional member dues here: <a href="http://re-wrenches.org" target="_blank">http://re-wrenches.org</a><br><br>List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br><br>Change listserver email address & settings:<br><a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br><br>There are two list archives for searching. When one doesn't work, try the other:<br><a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br><a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br><br>List rules & etiquette:<br><a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br><br>Check out or update participant bios:<br><a href="http://www.members.re-wrenches.org" target="_blank">http://www.members.re-wrenches.org</a><br><br></div></blockquote></div><br></div></div>_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div>