<div dir="ltr"><div>Jeremy,</div><div><br></div><div>I bought those once a long time ago but sorry, striking out finding documentation from where. Bought only once because it really is pretty simple and we just started making them ourselves.</div><div><br></div><div>The hardest part is getting a good, consistent and even bend. The ultimate rig (after lots of trial and error) was a large gas hot water tank. It had a whole perfectly down the center for the gas flu, we inserted a piece of 2" or 2-1/2" rigid pipe and then put the pipe on pipe rollers (so the tank was now horizontal and could roll freely.) Secure one end of your tubing to one end of the tank and then just slowly roll the tank around, wrapping the CU tubing as you go. With a little practice you can make them look perfect.</div><div><br></div><div>We used Type M soft CU.<br></div><div><br></div><div>While they are still on the tank, you lay a support 1/2" piece of hard CU tube perpendicular to the tubing coils and tack the coils to the support maybe every 2 or 3 coils. We would evenly space three supports around the coils. Run them a bit long on the bottom for temporary feet and longer still on the top for structure to hang them (assuming you are going at the top of your tank.)<br></div><div dir="ltr"><br></div><div>CU is pretty easy to work with but obviously stainless would be a whole different animal.<br></div><div dir="ltr"><br></div><div>Trying to dig up some photos of the rig but striking out there too, but here is a final product shot. Good luck,</div><div>-Nathan<br><img src="cid:ii_lehwn6e20" alt="Coils.jpg" width="318" height="492"><br><br></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Feb 22, 2023 at 6:05 PM Jerry Shafer via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto">Any plumbing supply shop has these, soft copper comes in 50 feet and up,you can use 1t2",5/8" or 3/4" I use double 1/2" and "T" it on top of the tank, <div dir="auto">Funtimes</div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Wed, Feb 22, 2023, 4:16 PM Jeremy Rodriguez via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Thermal Wrenches, <br>
can someone recommend a supplier for pre-coiled stainless or copper tube heat exchangers?<br>
<br>
<br>
Jeremy Rodriguez <br>
Solar Installation / Design<br>
All Solar, Inc.<br>
1453 M St. <br>
Penrose Colorado 81240<br>
<br>
Sent by Jeremy's iPhone. Sorry for typos and shorthand. <br>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div></div>