<div dir="ltr"><div class="gmail_default" style="font-family:times new roman,serif;font-size:large"><p class="MsoNormal" style="margin:0in;line-height:107%;font-size:11pt;font-family:Calibri,sans-serif"><span style="font-size:18pt;line-height:107%;background-image:initial;background-position:initial;background-size:initial;background-repeat:initial;background-origin:initial;background-clip:initial">Assuming this is a zero instantaneous no export, not on the
daily or monthly.   I have installed a few XW, and XW PRO
inverters, however, I have never done an instantaneous no export project
on the entire service.  The problem is the load.  Ideally you want to
monitor the service entrance and control off the service current.  This
would mean the total current would have to pass through the XW.  However, this would be a very limited
electrical use household, like an off-grid house.  For the No Export to work on a more
normal load, you want maximum current possible to pass through the XW (where
the control is) to the priority circuit panel, (you will want to measure these
loads allowing for non-coincidence).  You
will want to charge the batteries from solar only and deplete the battery to
about 15% SOC.  What you want to do is
sell all the solar that comes in, do not charge from the grid, to reduce the electric
bill the maximum amount.   I use an Egauge for measuring these
loads.  (PS) the XW has no monitoring of the
LiFe battery so use the charge controller Voltage to maintain SOC.  (PS) you may have to use the generator support
mode input.  I do not remember.  </span></p>

<p class="MsoNormal" style="margin:0in;line-height:107%;font-size:11pt;font-family:Calibri,sans-serif"><span style="font-size:18pt;line-height:107%;background-image:initial;background-position:initial;background-size:initial;background-repeat:initial;background-origin:initial;background-clip:initial">Sorry about my poor writing ability, hope this helps.  </span><span style="font-size:14pt;line-height:107%"></span></p></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Fri, Dec 23, 2022 at 3:45 PM Dave Angelini Offgrid Solar via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div style="font-size:12pt;font-family:Verdana,Geneva,sans-serif">
<div id="m_8012967077283025143signature">
<pre><span style="font-size:12pt">It can be done but it is not an easy job. You are 2 generations of XW back. <br><br>XW+ was good at this and XW pro was designed for this <br>along with being able to charge based on Soc (from the BMS) as well as voltage.<br><br></span><span style="font-size:12pt">Is this an insured home?  You might need a permit as this has to be legal for your area.  Out west of you is what we do.   Good Luck !<br><br><span>The main impact of Rule 21 for solar installers is that </span><strong>any of your installations in the state of California must now use Rule-compliant inverters</strong><span>.<br> In effect, these are smart inverters that have been certified as UL 1741-SA or that are listed on the California Energy Commission's compliant inverter<br> database.</span><br><br></span><br> </pre>
<pre><strong><span style="font-size:small">Dave Angelini Offgrid Solar
"we go where powerlines don't"
<a href="http://members.sti.net/offgridsolar/" rel="noopener" target="_blank">http://members.sti.net/offgridsolar/</a>
e-mail  <a href="mailto:offgridsolar@sti.net" target="_blank">offgridsolar@sti.net</a>
text 209 813 0060</span></strong></pre>
</div>
<p><br></p>
<p id="m_8012967077283025143reply-intro">On 2022-12-21 5:23 am, Jeremy Rodriguez via RE-wrenches wrote:</p>
<blockquote type="cite" style="padding:0px 0.4em;border-left:2px solid rgb(16,16,255);margin:0px">
<div style="margin:0px;padding:0px;font-family:monospace"><br>I’ve inherited a XW. 6048 system that we just installed a LiFePO4 battery bank with. <br>Has anyone successfully used Grid Support with Sell disabled? <br>This system never had an Interconnection Agreement with the utility co so it cannot sell. <br>Currently we have :<br>AC charger on , Multi Stage<br>PV input <br>Sell disabled <br>Grid Support disabled <br>There is no TOU metering. <br><br><br>Regards,<br><br>Jeremy Rodriguez <br>Solar Installation / Design<br>All Solar, Inc.<br>1453 M St. <br>Penrose Colorado 81240<br><br>Sent by Jeremy's iPhone. Sorry for typos and shorthand. <br>_______________________________________________<br>List sponsored by Redwood Alliance<br><br>Pay optional member dues here: <a href="http://re-wrenches.org" rel="noopener noreferrer" target="_blank">http://re-wrenches.org</a><br><br>List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br><br>Change listserver email address & settings:<br><a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noopener noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br><br>There are two list archives for searching. When one doesn't work, try the other:<br><a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noopener noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br><a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noopener noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br><br>List rules & etiquette:<br><a href="http://www.re-wrenches.org/etiquette.htm" rel="noopener noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br><br>Check out or update participant bios:<br><a href="http://www.members.re-wrenches.org" rel="noopener noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br><br></div>
</blockquote>
</div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div>