<html><head><meta http-equiv="Content-Type" content="text/html; charset=us-ascii"><meta name="Generator" content="Microsoft Word 14 (filtered medium)"><style><!--
/* Font Definitions */
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
@font-face
{font-family:Verdana;
panose-1:2 11 6 4 3 5 4 4 2 4;}
@font-face
{font-family:Georgia;
panose-1:2 4 5 2 5 4 5 2 3 3;}
@font-face
{font-family:Roboto;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri","sans-serif";}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-compose;
font-family:"Verdana","sans-serif";
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;
font-family:"Calibri","sans-serif";}
@page WordSection1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.WordSection1
{page:WordSection1;}
--></style></head><body lang="EN-US" link="blue" vlink="purple"><div class="WordSection1"><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif"">Friends:</span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif""> </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif"">Thanks to all of you that offered suggestions. I found what I needed for this project: Nassau National Cable offered a two wire, 14 AWG CU tray cable. Attached is the data sheet if anyone is interested. </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif""> </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif"">The vendor can be found at: </span><b><span style="font-family:"Georgia","serif";color:#9900ff"><a href="http://www.nassauelectrical.com/" target="_blank"><span style="color:#1155cc">www.nassaunationalcable.com</span></a></span></b><span style="font-size:9.5pt;font-family:Roboto;color:#500050">. </span><span style="font-size:12.0pt;font-family:"Verdana","sans-serif"">They were very responsive.</span><span style="font-size:9.5pt;font-family:Roboto;color:#500050"></span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif""> </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif"">The cable mated quite nicely with the small gauge leads on the low water sensor and even with a very tough jacket was small enough to fit alongside the pump power cables in the conduit at the well-head.</span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif""> </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif"">By the way, this installation used a Picocell 2000 pump controller which converts DC to single or three phase at 120 or 230 VAC. It is good up to 1 HP or a bit more. It is a nice product. I recommend an outboard DC switch and an adjacent J-box to hold service loops since the wiring compartment is quite small. The controller is set up with gland fittings to facilitate jacketed cables but we switched those out for NMLT. I have always preferred to protect wiring. </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif""> </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif"">As another aside, our local well technicians could not source a low water sensor for us. Thunderbird solar has them. Locally, the well technicians like using the Franklin pump-saver to protect a pump from dry running. I don’t prefer the pump-saver because they are fickle, expensive and require some duration of dry run before they shut down. We prefer a down-hole sensor. With the lowering of water tables here in the arid west, it is important to be able to protect well pumps from dry running and to provide for intermittent pumping to allow maximum production on slow-recharge wells. All of our wells will have low water sensors from now on.</span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif""> </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif"">William Miller</span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Verdana","sans-serif""> </span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial","sans-serif"">Miller Solar</span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial","sans-serif"">17395 Oak Road, Atascadero, CA 93422</span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial","sans-serif"">805-438-5600</span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial","sans-serif""><a href="http://www.millersolar.com/">www.millersolar.com</a></span></p><p class="MsoNormal"><span style="font-size:12.0pt;font-family:"Arial","sans-serif"">CA Lic. 773985</span></p><p class="MsoNormal"> </p><p class="MsoNormal"> </p></div></body></html>