<div dir="ltr">Buckling of the wall studs is most likely going to be the failure mode. You can use WebStructural to look at different designs. You'll find that accurately defining the constraints on the structural members is the most troublesome.<div><a href="https://webstructural.com/">https://webstructural.com/</a></div><div><br></div><div>Personally, I don't think that supporting a couple of thousand pounds of dead load hanging off the sides of $2 studs fastened with unknown fasteners into unknown top and bottom plates is a super great idea. I would do it on a poured concrete wall, but this sounds like it is asking for trouble.</div><div><br></div><div><br clear="all"><div><div dir="ltr" class="gmail_signature" data-smartmail="gmail_signature"><div dir="ltr"><div>-James Jefferson Jarvis<br>APRS World, LLC<br>+1-507-454-2727<br></div><a href="http://www.aprsworld.com/" target="_blank">http://www.aprsworld.com/</a><br></div></div></div><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 6, 2022 at 9:30 AM Jason Szumlanski via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto">2x4 studs have compressive force to hold up over 1,000 pounds each when constructing a load bearing wall, so I don't think that is a limiting factor. But I am not a structural engineer, so consulting one would not be a bad idea. <div dir="auto"><br></div><div dir="auto"><br></div><div dir="auto">Jason</div><div dir="auto"><br></div></div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 6, 2022, 10:21 AM Chris Sparadeo <<a href="mailto:sparadeo.chris@gmail.com" target="_blank">sparadeo.chris@gmail.com</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto">Thanks Jason,</div><div dir="auto"><br></div><div dir="auto">I’m still wondering if there is an IBC reference for weight. The Discover manual only states:</div><div dir="auto"><br></div><div dir="auto">“ For structural and seismic stability, the AES Battery must be mounted onto a vertical supporting surface strong enough to support a minimum of 227 kg (500 lbs) per battery. Failure to follow these instructions can result in death or serious injury.”</div><div dir="auto"><br></div><div dir="auto">Other than asking a structural engineer, how can I be sure that the wall is rated to 4,500 lbs? </div><div><br><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 6, 2022 at 9:20 AM Jason Szumlanski via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" rel="noreferrer" target="_blank">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"><div dir="auto">That won't be a problem as long as they are spread across several studs. Even 2x4 studs would be fine. Check the installation manual for details. The shear and pull out strength of the fasteners will be the limiting factor, not the wall itself unless very poorly constructed. <div dir="auto"><br></div><div dir="auto"><a href="https://assets.discoverbattery.com/documents/03_aes/805_product_manual/gui-aes-wall-mount-bracket-installation-guide.pdf" rel="noreferrer" target="_blank">https://assets.discoverbattery.com/documents/03_aes/805_product_manual/gui-aes-wall-mount-bracket-installation-guide.pdf</a></div><div dir="auto"><br></div><div dir="auto">Jason Szumlanski</div><div dir="auto">Florida Solar Design Group </div><div dir="auto"><br></div><div dir="auto"><br></div></div><br><div class="gmail_quote"></div><div class="gmail_quote"><div dir="ltr" class="gmail_attr">On Tue, Sep 6, 2022, 8:59 AM Chris Sparadeo via RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" rel="noreferrer" target="_blank">re-wrenches@lists.re-wrenches.org</a>> wrote:<br></div></div><div class="gmail_quote"><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex"></blockquote></div><div class="gmail_quote"><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">Hi all,<div dir="auto"><br></div><div dir="auto">I have a project where I am contemplating hanging 9 Discover AES batteries on a wall. Each battery is around 200 lbs, and although the stud wall is a bulky 2”x6” with 16” OC…I have apprehensions that hanging almost a ton of battery on the wall is a good idea. I’ve seen it done in other install photos, however I can’t seem to find and good building code that would inform my decision. </div><div dir="auto"><br></div><div dir="auto">Does anyone out there have a building code reference or experience that might help? </div><div dir="auto"><br></div><div dir="auto">Thanks!</div><div dir="auto"><br></div><div dir="auto">-Chris </div>-- <br><div dir="ltr"><div dir="ltr"><div><div dir="ltr"><div dir="ltr"><div>Chris Sparadeo</div><div><br></div><div><br></div><div>C_802-369-4458</div><div>H_802-728-3059</div><div></div></div></div></div></div></div></blockquote></div><div class="gmail_quote"><blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left:1px solid rgb(204,204,204);padding-left:1ex">
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer noreferrer noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer noreferrer" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer noreferrer noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" rel="noreferrer" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div></div>-- <br><div dir="ltr"><div dir="ltr"><div><div dir="ltr"><div dir="ltr"><div>Chris Sparadeo</div><div><br></div><div><br></div><div>C_802-369-4458</div><div>H_802-728-3059</div><div></div></div></div></div></div></div>
</blockquote></div>
_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
Pay optional member dues here: <a href="http://re-wrenches.org" rel="noreferrer" target="_blank">http://re-wrenches.org</a><br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
There are two list archives for searching. When one doesn't work, try the other:<br>
<a href="https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/" rel="noreferrer" target="_blank">https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/</a><br>
<a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" rel="noreferrer" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" rel="noreferrer" target="_blank">http://www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" rel="noreferrer" target="_blank">http://www.members.re-wrenches.org</a><br>
<br>
</blockquote></div>