<div dir="ltr">Hi William,<div><br></div><div>Yes the Outback shunt should be fine for this application.  See page 72 here for the calibration: <a href="http://files.sma.de/dl/15216/SI4548-6048-US-BE-en-20.pdf">http://files.sma.de/dl/15216/SI4548-6048-US-BE-en-20.pdf</a></div><div>As far as verifying with your clamp meter, I'd say if you can verify within 15% (remember to check polarity) then it is properly calibrated.  It should do a better job than your clamp meter, but that will help make sure you are close.  Check parameter 120.06 TotBatCur to see what the Sunny Island thinks the battery current is (in older versions of firmware it may be elsewhere).  I have found that with my fluke DC clamp meter (don't know the model off the top of my head), I am easily within 5% when the current is around 20ADC.</div><div><br></div><div>Good Luck</div></div><div class="gmail_extra"><br><div class="gmail_quote">On Thu, Feb 12, 2015 at 8:58 AM, William Miller <span dir="ltr"><<a href="mailto:william@millersolar.com" target="_blank">william@millersolar.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex"><div dir="auto"><div>Mac:</div><div><br></div><div>Thanks for the advice. We will install the shunt today. A few more questions:</div><div><br></div><div>1.  Will the Outback 50ma shunt be compatible. My research indicates the value is correct. </div><div><br></div><div>2.  DC clamps are notoriously inaccurate, particularly at low amperages. Will this be a problem, or is shorting the leads adequate?</div><div><br></div><div>Thanks again. </div><div><br></div><div>William Miller</div><div><br></div><div>PS:  We looked at the Midnite cabinets but they put the OPCD too far from the batteries.</div><div><br></div><div>William</div><span class=""><div><br><br></div><div><br>On Feb 12, 2015, at 4:45 AM, Mac Lewis <<a href="mailto:maclewis1@gmail.com" target="_blank">maclewis1@gmail.com</a>> wrote:<br><br></div></span><span class=""><blockquote type="cite"><div><div dir="ltr">Hi William,<div><br></div><div>I want to talk directly to your problem at hand.  I think installing the shunt and properly calibrating it, will fix this system .  In a DC coupled system with a Sunny Island, it is imperative that you use a shunt, unless you are using the Midnite charge controllers with the communications to accurately report all charging (or the non-UL listed SMA charge controllers).  There are so many functions and calculations that the Sunny Island performs that needs accurate SOC calculations.  All of the shutdowns that you are seeing are resulting from faulty SOC measurements.  I wouldn't believe the reported state of health either, because it is using the faulty SOC measurements.  Don't believe state of health until you have a couple of months of operation with the shunt.</div><div><br></div><div><b>Right now, with the system as is, it isn't accounting for the charge coming from the charge controller(s)</b>.  It is shutting down because its only accounting for AC power processed through the Sunny Island.  I once had a Sunny Island system with an improperly calibrated shunt and it acted just as you describe, strange shutdowns, bad SOC output etc.  After I got it calibrated, it has worked flawlessly.</div><div><br></div><div>Take your time when you are calibrating the shunt.  Follow the (odd) directions perfectly and it should work.  Verify Sunny Island readings match your DC clamp meter and you should be good.</div><div><br></div><div><br></div></div></div></blockquote><blockquote type="cite"><div><span></span><br></div></blockquote></span></div><br>_______________________________________________<br>
List sponsored by Redwood Alliance<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change listserver email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html" target="_blank">http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out or update participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
<br></blockquote></div><br><br clear="all"><div><br></div>-- <br><div class="gmail_signature"><div><br></div><div><font color="#305A78" face="'times new roman', serif"><br></font></div><div><br></div>Mac Lewis<br><br><span style="font-family:'Times New Roman';font-size:medium;color:rgb(255,153,0)"><b><font face="Arial, Helvetica, sans-serif" size="3"><p align="left"><font color="#000000" face="Verdana, Arial, Helvetica, sans-serif"><span style="font-size:small"><span style="font-family:arial;font-weight:normal;color:rgb(48,90,120)"><font face="'times new roman', serif">"Yo solo sé que no sé nada." </font><span style="font-weight:700;color:rgb(104,104,104)"><font face="'times new roman', serif">-Sócrates</font></span></span></span></font></p></font></b></span></div>
</div>