<p dir="ltr">OK So if you only have the 600 watts per day when you are either on shore power or on a genny can you design the system to not be needed when they are off and kill that load<br>
Jerry</p>
<div class="gmail_quote">On Feb 13, 2014 11:51 AM, "Larry Crutcher, Starlight Solar Power Systems" <<a href="mailto:larry@starlightsolar.com">larry@starlightsolar.com</a>> wrote:<br type="attribution"><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
<div style="word-wrap:break-word">Hi Jerry,<div><br></div><div>The no-fault condition from the CPU is +12Vdc. A fault causes 0 volts. These are the contactors I plan to use: <a href="http://www.alliedelec.com/search/productdetail.aspx?SKU=70062412" target="_blank">http://www.alliedelec.com/search/productdetail.aspx?SKU=70062412</a></div>
<div><br></div><div>Larry</div><div><br></div><div> <br>
<br><div><div>On Feb 13, 2014, at 12:38 PM, Jerry Shafer <<a href="mailto:jerrysgarage01@gmail.com" target="_blank">jerrysgarage01@gmail.com</a>> wrote:</div><br><p dir="ltr">So Ian clear does the fault activate the relay or does the absence of the fault activate the relay because its usually best to have a absent or no fault hold the relay on and if anything fails as a the relay will rest this can be done with motorized on or contactor high load switch, you should also look at the switch AIC rating also<br>


Jerry</p>
<div class="gmail_quote">On Feb 11, 2014 4:43 PM, "Larry Crutcher, Starlight Solar Power Systems" <<a href="mailto:larry@starlightsolar.com" target="_blank">larry@starlightsolar.com</a>> wrote:<br type="attribution">
<blockquote class="gmail_quote" style="margin:0px 0px 0px 0.8ex;border-left-width:1px;border-left-color:rgb(204,204,204);border-left-style:solid;padding-left:1ex">
<div style="word-wrap:break-word">Hello Wrenches,<div><br></div><div>We're preparing to offer Lithium batteries to some of our customers as a replacement to lead acid in recreational vehicles. RV batteries can have multiple charge sources simultaneously so I have worked out protective circuitry to interface with a EMS computer. To insure failsafe operation, I need to install 2 solenoids that will be active 24/7, opening only when fault conditions are met.</div>

<div><br></div><div>The solenoids I have looked at (200 amp) have a coil current of about 1 ampere each which equates to 600Wh daily consumption. I'de like to reduce that BUT the computer only provides a +12v or 0 volt state. </div>

<div><br></div><div><ul><li>Does anyone know of a latching solenoid that will work with a 12v hi/lo voltage state,</li><li>OR an interface or circuit for hi/lo to control latching relay</li><li>OR a solenoid with a very low quiescent current when on? </li>

</ul></div><div><br></div><div>Many thanks in advance, </div><div><br></div><div><div>Larry Crutcher</div></div></div><br>
<br></blockquote></div><br></div></div></div><br>_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Change email address & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
<br></blockquote></div>