It does "take". Your charge controller controls the load and current, hence the name "controller". It is not a fixed resistance. If you program a charge rate limit, the controller will control the current flow to limit the charge rate, hence it is "taking" a certain current up to the limit of the source's ability to supply that current but not above, regardless of the size of the array.<br>
<br><div class="gmail_quote">On Wed, Oct 24, 2012 at 10:17 PM, Richard L Ratico <span dir="ltr"><<a href="mailto:Richard.L.Ratico@valley.net" target="_blank">Richard.L.Ratico@valley.net</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Huh? The equipment does not "take" or "draw" anything. The electrical pressure<br>
of the source, called voltage, forces electrons through the load. Electrons per<br>
unit time are called current. The current is only limited by the resistance of<br>
the load, in accord with Ohms Law. The resistance of the load acts as a valve or<br>
choke point in the circuit, thus limiting the current. In the case Allan<br>
describes, the battery is the primary resistance in the circuit. If the battery<br>
was large enough and, or, sufficiently discharged (low resistance), and the<br>
source could provide enough current, the C-40 would "Toast".<br>
<br>
Dick Ratico<br>
<div class="im"><br>
--- You wrote:<br>
Because it is not 80 amps current flowing, it is a capacity of 80 amps.<br>
Think of it this way. Your toaster is plugged into an outlet that is<br>
powered by the grid. The grid has infinite capacity. Why doesn't your<br>
toaster explode? Because it takes the current it needs. Now, increase the<br>
voltage and you may have a runaway current situation, but at the design<br>
voltage the equipment takes the current it needs up to the limit if the<br>
supply.<br>
</div>--- end of quote ---<br>
<div class="HOEnZb"><div class="h5">_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Options & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
</div></div></blockquote></div><br><br clear="all"><div><br></div>-- <br>Chris Mason<div>President, Comet Systems Ltd</div><div><a href="http://www.cometenergysystems.com" target="_blank">www.cometenergysystems.com</a></div>
<div>Cell: 264.235.5670</div><div>Skype: netconcepts</div><br>