That's the conclusion that I came to after speaking with SunPower about it. Apparently the bracket protrudes 1.39" below the module frame (no mention of that on the spec sheet). Until I get some rail mounted ACPV modules under my belt I'm not going to try a S-5 direct mount (S-5-PV). <div>

<br clear="all">Jason Szumlanski<div>Fafco Solar</div><div><br></div><br>
<br><br><div class="gmail_quote">On Fri, May 18, 2012 at 9:09 AM, Isaac Opalinsky <span dir="ltr"><<a href="mailto:iopalinsky@gmail.com" target="_blank">iopalinsky@gmail.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">

<div class="gmail_quote"><div>Jason,</div><div><br></div><div>Will you be doing a direct mount to S-5!, or will you use rails?<br><br></div><div>If using rails, there should be no significant difference from using ACPV on a shingle roof with rails.  If doing a direct mount, I imagine it would be a lot like using ACPV with Smart Mount, which attaches directly to the roof decking.  Wire management is the main challenge; with both Smart Mount and S-5! direct mount, you have very little clearance below the modules.  The receptacle is designed to mount below the frame of the modules, and you will have little clearance to pull out any remaining slack.  Additionally, you will need to make sure that the receptacle brackets to not conflict with any seams.  It's been a while since I've done an S-5! direct mount, but I seem to recall having less than an inch between the bottom of a module frame and the top of the seam; this will not be enough to support the receptacle.  You may need to plan the module placement very carefully to avoid this issue.</div>


<div><br></div><div>Please contact me off line at <a href="mailto:isaac.opalinsky@sunpowercorp.com" target="_blank">isaac.opalinsky@sunpowercorp.com</a> if you want to talk about your specific application and how to make it work.</div>

<div>
<br></div><div>Regards,</div><div>Isaac Opalinsky</div><div>Technical Trainer</div><div>SunPower</div><div> </div><blockquote class="gmail_quote" style="margin:0 0 0 .8ex;border-left:1px #ccc solid;padding-left:1ex">
Message: 2<br>
Date: Tue, 15 May 2012 15:56:41 -0400<br>
From: Jason Szumlanski <<a href="mailto:jason@fafcosolar.com" target="_blank">jason@fafcosolar.com</a>><br>
To: RE-wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank">re-wrenches@lists.re-wrenches.org</a>><br>
Subject: [RE-wrenches] SunPower ACPV E18/225W Module with S-5-PV<br>
        Clamps<br>
Message-ID:<br>
        <CAJJtG3r1uv5Q4U3KrNfeFv=_<a href="mailto:ph6f6k7gj2qCoaPugf_25KvmzA@mail.gmail.com" target="_blank">ph6f6k7gj2qCoaPugf_25KvmzA@mail.gmail.com</a>><br>
Content-Type: text/plain; charset="iso-8859-1"<br>
<br>
Has anyone done this combination yet? Is the inverter and cable system<br>
tucked up nicely under the module to allow this to work?<br>
<br>
Jason Szumlanski<br>
Fafco Solar<br></blockquote></div>
<br>_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Options & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
<br></blockquote></div><br></div>