Benn~ If the company that built those batteries is a major brand name, I advise that you add neither water nor acid to the new cells. Check with the mfr, but most of the serious mfrs are using robotic fill equipment that is very precise. <br>
<br>If some of the cells are older stock they may have self discharged a bit and the electrolyte level rises & falls like the tide based on state of charge. I'll bet if you can EQ the batts to reach equal state of charge, you also will find the electrolyte level to equalize. <br>
<br>Jolliness, <br><br clear="all">Mick Abraham, Proprietor<br><a href="http://www.abrahamsolar.com">www.abrahamsolar.com</a><br><br>Voice: 970-731-4675<br>
<br><br><div class="gmail_quote">On Thu, Mar 24, 2011 at 11:20 AM, Nick Soleil <span dir="ltr"><<a href="mailto:nicksoleilsolar@yahoo.com">nicksoleilsolar@yahoo.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="margin: 0pt 0pt 0pt 0.8ex; border-left: 1px solid rgb(204, 204, 204); padding-left: 1ex;">
<div><div style="font-family: arial,helvetica,sans-serif; font-size: 12pt;">Hi Benn:<br> Perhaps those batteries have just been sitting a little while, and need a recharge. Generally speaking, if you find that the batteries test reading are a little low, they are probably just a little discharged. After recharging the batteries, test them again. If those readings are low, then contact the manufacturer with the data. I have had great luck with battery manufacturers warranting their defective batteries in warranty.<br>
<div> </div>Nick Soleil<br>Project Manager<br>Advanced Alternative Energy Solutions, LLC<br>PO Box 657<br>Petaluma, CA 94953<br>Cell: 707-321-2937<br>Office: 707-789-9537<br>Fax: 707-769-9037<div><br></div><div style="font-family: arial,helvetica,sans-serif; font-size: 12pt;">
<br><div style="font-family: times new roman,new york,times,serif; font-size: 12pt;"><font face="Tahoma" size="2"><hr size="1"><b><span style="font-weight: bold;">From:</span></b> benn kilburn <<a href="mailto:benn@daystarsolar.ca" target="_blank">benn@daystarsolar.ca</a>><br>
<b><span style="font-weight: bold;">To:</span></b> Wrenches <<a href="mailto:re-wrenches@lists.re-wrenches.org" target="_blank">re-wrenches@lists.re-wrenches.org</a>><br><b><span style="font-weight: bold;">Sent:</span></b> Thu, March 24, 2011 9:43:20 AM<br>
<b><span style="font-weight: bold;">Subject:</span></b> [RE-wrenches] Testing new batteries<br></font><br>
I'm curious of others experiences with testing "new" batteries right from the mfgr, before putting them into service. I'm not talking about load testing, i mean just basics...voltage, specific gravity and electrolyte level.<div>
<br></div><div>I recently received some batteries (24 x 2V) and before putting them to work i tested all the voltages, SG's and levels. Voltages were all with-in 0.016 V (2.1-2.084). The SG's were within 0.037 (1.281-1.244). Yes, the one with the lowest SG also had the lowest V. </div>
<div><br></div><div>What concerns me a bit more than the few cells with lower SG is the consistent low levels of electrolyte. All cells were between 3/4" and 1-1/2" below full, which is 1/4" below the bottom of the vent well tube.... with one exception that was bang-on full. Interestingly, the one full battery was the only one with a different date code than the rest. </div>
<div><br></div><div>Should the
various levels of electrolyte mentioned be acceptable when a battery is brand new, straight from the mfgr? How bout the SG's?</div><div><br></div><div>I'm considering adding electrolyte from a local battery shop instead of distilled water to top up all the batteries. Comments?</div>
<div><br></div><div>Very thankful for the wealth of knowledge and experience on this list,</div><div>benn<br><br><span style="color: rgb(0, 32, 96);"><font face="'Franklin Gothic Medium'">DayStar Renewable Energy Inc. </font></span><div>
<div><font face="'Franklin Gothic Medium'"><a href="mailto:benn@daystarsolar.ca" target="_blank">benn@daystarsolar.ca</a></font></div><div><font face="'Franklin Gothic Medium'">780-906-7807 </font></div><div>
<font face="'Franklin Gothic Medium'">HAVE A SUNNY DAY
</font></div><div><br></div></div><br><br></div> </div></div>
</div><br>
</div><br>_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Options & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
<br></blockquote></div><br>