To use a 1/4" fastener with an L-foot mounting slot that's bigger, one could use a "shoulder washer" or a "flange bushing". Those might be good search terms to use at, say, <a href="http://mcmaster.com">mcmaster.com</a><br>

<br>One must wonder if the pull-out resistance of the 1/4" Tek screw is adequate for the wind-loading etc. There's some math to be done which may point to the need for bigger diameter screws anyway.<br><br>Jolliness,<br>

<br clear="all">Mick Abraham, Proprietor<br><a href="http://www.abrahamsolar.com">www.abrahamsolar.com</a><br><br>Voice: 970-731-4675<br>
<br><br><div class="gmail_quote">On Fri, Oct 23, 2009 at 9:18 AM, jay peltz <span dir="ltr"><<a href="mailto:jay@asis.com">jay@asis.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">

HI Guys,<br>
<br>
Check out dynamic fastener,<br>
<br>
they have a lot of great stuff.<br>
<br>
Including self drilling 1/4x 20 SS screws and larger.<br>
<br>
jay<br>
<br>
peltz power<div><div></div><div class="h5"><br>
On Oct 23, 2009, at 3:12 AM, Carl Adams wrote:<br>
<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
Hello Wrenches,<br>
<br>
Pulling up this thread from earlier in the year.  I have a couple of<br>
upcoming jobs where I am attaching PV mounting structure  as follows<br>
Job 1) LFoot to metal roof into Z purlin, and Job 2) FastJack to metal<br>
roof into bar joist.<br>
<br>
In both of the applications I'm considering the Tek screw type<br>
attachment to the building steel.  Both the L foot and FastJack are<br>
sized for a 5/16 - 3/8 lag or bolt.  Most of the self tappers I see<br>
are 1/4" max diameter.  Should I be concerned about the undersized fit<br>
of the fastener in the mounting attachment or are there large Tek type<br>
screws out there I'm not finding?<br>
<br>
Does anyone have pullout strengths for this type of attachment?<br>
<br>
With Regards<br>
Carl Adams<br>
NABCEP Certified PV Installer<br>
SunRock Solar, LLC<br>
<br>
On Thu, Feb 5, 2009 at 6:51 PM, Peter Parrish<br>
<<a href="mailto:peter.parrish@calsolareng.com" target="_blank">peter.parrish@calsolareng.com</a>> wrote:<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
Does anyone have a source for stainless steel, self tapping Tek screws? I<br>
could use some #10/3-4 and #10/1-1/2. If they have the little cap and<br>
neoprene washer that would be even better!<br>
<br>
- Peter<br>
<br>
Peter T. Parrish, President<br>
California Solar Engineering, Inc.<br>
820 Cynthia Ave., Los Angeles, CA 90065<br>
Ph 323-258-8883, Mobile 323-839-6108, Fax 323-258-8885<br>
CA Lic. 854779, NABCEP Cert. 031806-26<br>
<a href="mailto:peter.parrish@calsolareng.com" target="_blank">peter.parrish@calsolareng.com</a><br>
<br>
<br>
_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Options & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
<br>
</blockquote>
_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Options & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
</blockquote>
<br>
_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Options & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
</div></div></blockquote></div><br>