We prefer pole mounts as well for ease of adjust ability, simple to brush off, and can accommodate our 55deg winter tilt.  We like DPW as well.  If the client or site is stuck on the roof mount we always go flush and try to keep the array as high on the roof as we can while still giving a little space for wind sheer.  We have seen snow build up on the back side of the array (north) that gets shaded and begins to ice dam.  If unmaintained in the right conditions you could get buildup and stress behind the array.  The solution is maintenance and the right client will shovel their roof behind the tilted modules.  We partnered on a job like Jay talked about  I attached a pic of that job.  It works great!  We simply welded brackets along the pole and attached to the side of the cabin.  Also attached a pic of  some roof damage on a unmaintained roof valley. Both jobs are at about 10,500' Irwin CO. <br>

<br><div class="gmail_quote">On Sat, Aug 15, 2009 at 7:51 PM, R. Walters <span dir="ltr"><<a href="mailto:walters@taosnet.com" target="_blank">walters@taosnet.com</a>></span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">

<div><br>
On Aug 15, 2009, at 6:49 PM, jay peltz wrote:<br>
<br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
I don't have a photo, but have seen a pole mount, in the ground, run up the side of the building, supported by the building by a bracket,  which can mount a tracking or non tracking pole mount.<br>
</blockquote>
<br>
</div><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
jay<br>
<br>
</blockquote>
<br>
<br>
We've done mounts like this before, when the roof was too sketchy to mount to, or an off grid system with a roof not facing close enough to south. It works pretty well: no penetrations or loading on the roof, still allows one bolt  tilt adjust,  azimuth to due south regardless of building orientation, etc.<br>


We normally would sit the pole in concrete, and then attach it with unistrut to the wall in a couple of spots. The unistrut would be long enough to catch 2 or 3 wall studs, and then attach to the pipe with  a 6" unistrut  clamp.<br>


As better roof mounting products have become available, we have been moving away from this method. Also, Grid tie just isn't near as critical for panel orientation, where as a small off-grid system in the winter really needs to be tilted to at least 30 deg, and within 20 deg of south to work right.<br>


Funny teaching us old off gridders to quit tilting, etc. with grid tie. Bill Brooks had some humorous examples of off grid sensibility applied in very ugly fashion to grid tie systems. At some point, I think NABCEP should consider separate certifications, as Off grid and grid tie have such different design requirements.<br>


<br>
Ray Walters<div><div></div><div><br>
_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Options & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
</div></div></blockquote></div><br>