<div>Just had 1 fail that was probably 8 years old. Took 2 - 3 weeks for the replacement to arrive, the factory was out of boards. The replacement was damaged, (in shipping?) and too 3 more weeks to get a replacement. The new ones are made by Siemens if i understood correctly. She is now running on a repaired original board with the promise of a new one when they arrive.</div>

<div>I think this was just a fluke, they have always been relatively fast with parts.</div>
<div> </div>
<div>The old boards had a lousy rep from my opinion. On mod sine the reverse relay kept going bad. I have one in my washer now, to cheap to change it and they don't have repair available on the old boards.<br></div>
<div>I like the washers, and I guess that normally when a washer failed we would just buy a new one, with the Stabers we change the board and keep using them.</div>
<div> </div>
<div>I did have one that needed the tub bearings replaced, not a hard job. If I ever do it again I will probably press new bearings into the carrier myself, but that's just my nature.</div>
<div> </div>
<div>Just my opinion, and I've got plenty of those.</div>
<div> </div>
<div>Bob</div>
<div><br> </div>
<div class="gmail_quote">On Tue, Jun 2, 2009 at 9:04 AM, Larry Brown <span dir="ltr"><<a href="mailto:sunmountain@netstep.net">sunmountain@netstep.net</a>></span> wrote:<br>
<blockquote class="gmail_quote" style="PADDING-LEFT: 1ex; MARGIN: 0px 0px 0px 0.8ex; BORDER-LEFT: #ccc 1px solid">Wrenches,<br><br>Has anyone had a problem with the control boards on Staber washing machines?<br>We have had 3 control boards fail in a relatively short time frame on the same machine<br>
Staber has replaced the boards each time<br>The last one was after completing a load of laundry and then starting a second load twenty minutes later and having the brand new, just installed replacement control board fail again<br>
This is a dedicated washing machine outlet with additional surge protection<br>No other motors or electronics have experienced any problems<br>This house has a grid-tied system with a Xantrex 2.8 kw inverter<br>All failures have been in the morning around  9-10 am<br>
<br>Any ideas or recommendations?<br><br>Thanks<br>Larry Brown<br>Sun Mountain<br><br>_______________________________________________<br>List sponsored by Home Power magazine<br><br>List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>Options & settings:<br><a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br><br>List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>List rules & etiquette:<br><a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br><br>Check out participant bios:<br><a href="http://www.members.re-wrenches.org/" target="_blank">www.members.re-wrenches.org</a><br>
<br></blockquote></div><br>