<html xmlns:v="urn:schemas-microsoft-com:vml" xmlns:o="urn:schemas-microsoft-com:office:office" xmlns:w="urn:schemas-microsoft-com:office:word" xmlns:m="http://schemas.microsoft.com/office/2004/12/omml" xmlns="http://www.w3.org/TR/REC-html40">
<head>
<meta http-equiv=Content-Type content="text/html; charset=us-ascii">
<meta name=Generator content="Microsoft Word 12 (filtered medium)">
<style>
<!--
/* Font Definitions */
@font-face
{font-family:"Cambria Math";
panose-1:2 4 5 3 5 4 6 3 2 4;}
@font-face
{font-family:Calibri;
panose-1:2 15 5 2 2 2 4 3 2 4;}
/* Style Definitions */
p.MsoNormal, li.MsoNormal, div.MsoNormal
{margin:0in;
margin-bottom:.0001pt;
font-size:11.0pt;
font-family:"Calibri","sans-serif";}
a:link, span.MsoHyperlink
{mso-style-priority:99;
color:blue;
text-decoration:underline;}
a:visited, span.MsoHyperlinkFollowed
{mso-style-priority:99;
color:purple;
text-decoration:underline;}
span.EmailStyle17
{mso-style-type:personal-compose;
font-family:"Calibri","sans-serif";
color:windowtext;}
.MsoChpDefault
{mso-style-type:export-only;}
@page Section1
{size:8.5in 11.0in;
margin:1.0in 1.0in 1.0in 1.0in;}
div.Section1
{page:Section1;}
-->
</style>
<!--[if gte mso 9]><xml>
<o:shapedefaults v:ext="edit" spidmax="1026" />
</xml><![endif]--><!--[if gte mso 9]><xml>
<o:shapelayout v:ext="edit">
<o:idmap v:ext="edit" data="1" />
</o:shapelayout></xml><![endif]-->
</head>
<body lang=EN-US link=blue vlink=purple>
<div class=Section1>
<p class=MsoNormal>We have an off grid system experiencing charge controller
issues. 3.24kW PV array (18) Evergreen ES-180’s in (6) strings of (3) modules
in series. Approximately 77 VDC Vmp, 60 Amps typically highest charging amps
into a 33.6kWh (rated storage) 48 volt battery bank. Charge controller originally
was an Apollo T-80 that never worked correctly (lots of various issues, we
ended up trying three different Apollo’s before the homeowner wanted us
to try another controller). We went with a tried and true Out Back MX60 as the
80 Amp Flex was not available yet. We knew the MX 60 was outside it’s
recommended PV array capabilities but we needed to get the client’s PV system
charging the battery bank ASAP. We planned on upgrading to the FM-80 when
available. <o:p></o:p></p>
<p class=MsoNormal><o:p> </o:p></p>
<p class=MsoNormal>The MX-60 worked flawlessly for several months until it
failed to control absorption charging. It would allow the batteries to charge
at bulk voltage (58.8) for hours with out switching to float (54). Absorption
time was set to two hours. Resetting and reprogramming did not resolve this
situation and the batteries were being overcharged when a couple of sunny
days were strung together.<o:p></o:p></p>
<p class=MsoNormal><o:p> </o:p></p>
<p class=MsoNormal>We swapped in a new FM-80 controller on April 2<sup>nd</sup>
and it worked perfectly until today. It was a sunny day and the FM-80 was in
absorption mode by noon time. The homeowner noticed at 2:30pm that the FM was
not in float as it should have been. It was a typical sunny day with no big
loads on. The homeowner reported that the FM-80 was repeatedly going through a
6 minute cycle. Snooze for 5 minutes, wakeup 5 seconds, tracking 10 sec, bulk
30 sec, absorb charge 20 sec, and back to snooze where it began another identical
cycle. The batteries were 100% charged by 2:000pm, the battery voltage was at
53.5VDC (two OB VFX3648’s ON powering lights and drawing 5 amps DC) when
the FM-80 was not in bulk, or absorb charge. When in bulk charge the PV amps (35A
mid afternoon, warm day) were connected to the battery bank the battery voltage
climbed back up to 58 volts quickly. The “tech” we called at Out Back
was not very helpful, “never heard of this situation” and tried to blame
it on poor battery connections, he could not understand why the battery
voltage would be 53.5V with a 5 Amp load and then 58 volts 30 seconds later
when 35 amps were charging into the batteries on a 100% charged battery bank. <o:p></o:p></p>
<p class=MsoNormal><o:p> </o:p></p>
<p class=MsoNormal>Anyone else had an issue like this? Any advice?<o:p></o:p></p>
<p class=MsoNormal><o:p> </o:p></p>
<p class=MsoNormal>Thanks,<o:p></o:p></p>
<p class=MsoNormal>Dave<o:p></o:p></p>
<p class=MsoNormal><o:p> </o:p></p>
<p class=MsoNormal><i>David Palumbo, President<o:p></o:p></i></p>
<p class=MsoNormal><i>Independent Power LLC<o:p></o:p></i></p>
<p class=MsoNormal><i>462 Solar Way Drive<o:p></o:p></i></p>
<p class=MsoNormal><i>Hyde Park, VT 05655<o:p></o:p></i></p>
<p class=MsoNormal>NABCEP Certified<o:p></o:p></p>
<p class=MsoNormal><i>www.independentpowerllc.com <o:p></o:p></i></p>
<p class=MsoNormal><o:p> </o:p></p>
</div>
</body>
</html>