We had an unusual roofing situation (corrugated fiberglass with rails attached to purlins underneath) which put the SunFrame rail much lower than it would normally be. Also, we had Sharp modules in landscape orientation (to match the purlin spacing), so the module frames came out past the L-feet and we had to mount the inverters under the L-feet instead of on top. Anyway - good to know there aren't usually tolerance issues. The L-feet are definitely the way to go to attach the microinverters to SunFrame.<br>
<br>Dana<br><br>-- <br>Dana Brandt<br>Ecotech Energy Systems, LLC<br><a href="http://www.ecotechenergy.com">www.ecotechenergy.com</a><br><a href="mailto:dana@ecotechenergy.com">dana@ecotechenergy.com</a><br>360.510.0433<br>
<br><br><div class="gmail_quote">On Fri, Feb 6, 2009 at 6:56 PM, Troy Harvey <span dir="ltr"><<a href="mailto:taharvey@heliocentric.org">taharvey@heliocentric.org</a>></span> wrote:<br><blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
<div class="Ih2E3d"><br>
<blockquote class="gmail_quote" style="border-left: 1px solid rgb(204, 204, 204); margin: 0pt 0pt 0pt 0.8ex; padding-left: 1ex;">
For design reasons we were forced to use Unirac SunFrame rail which required some extra effort and tight tolerances in mounting the inverters to it. If at all possible use a SolarMount-type rail. This is what the inverters were designed for.<br>

</blockquote>
<br>
<br></div>
We've used enphase with sunframe too. What we did was mount the inverter on two inverted L-feet. Worked really nicely, no tolerance problems.<br><font color="#888888">
<br>
Troy Harvey<br>
---------------------<br>
Heliocentric<br>
801-453-9434<br>
<a href="mailto:taharvey@heliocentric.org" target="_blank">taharvey@heliocentric.org</a></font><div><div></div><div class="Wj3C7c"><br>
<br>
_______________________________________________<br>
List sponsored by Home Power magazine<br>
<br>
List Address: <a href="mailto:RE-wrenches@lists.re-wrenches.org" target="_blank">RE-wrenches@lists.re-wrenches.org</a><br>
<br>
Options & settings:<br>
<a href="http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org</a><br>
<br>
List-Archive: <a href="http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org" target="_blank">http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org</a><br>
<br>
List rules & etiquette:<br>
<a href="http://www.re-wrenches.org/etiquette.htm" target="_blank">www.re-wrenches.org/etiquette.htm</a><br>
<br>
Check out participant bios:<br>
<a href="http://www.members.re-wrenches.org" target="_blank">www.members.re-wrenches.org</a><br>
<br>
</div></div></blockquote></div><br><br clear="all"><br>