[RE-wrenches] Over voltage error message
drake.chamberlin at redwoodalliance.org
drake.chamberlin at redwoodalliance.org
Tue Jul 18 16:12:20 PDT 2017
Hi Matt,
There is no additional data monitoring. I haven't been able to make it
out there yet to check the parameters.
The main reason the client is so worried is that she got a message
that I'm not familiar with that said something to the effect that the
problem had to be solved before the event light could be turned off.
I did not see this personally, and haven't encountered this message
before. I will need to see if the manual can shed any light on how to
turn off the light. .
Thanks,
Drake
----- Original Message -----
From: "RE-wrenches" <re-wrenches at lists.re-wrenches.org>
To:"re-wrenches" <re-wrenches at lists.re-wrenches.org>
Cc:
Sent:Tue, 18 Jul 2017 05:56:15 -0400
Subject:[RE-wrenches] Over voltage error message
Greetings Drake,
This is interesting. I have Grid-tied OutBack Radian GS8048A with
MidNite Classic 200 systems in the field, but don't believe I've seen
this issue before. (But certainly have seen many strange MATE3 &
OpticsRE issues)
Here are a few questions that come to mind:
What is the Radian "Sell" voltage set at? Has this setting been
checked since this issue was reported? Have the Classic 200 settings
been checked to make sure they are set where they should be?
Does the system have any data monitoring on the charge controller
and/or battery system independent of the Radian inverter? If so, any
information similar to the Events logged on the MATE3?
Does this system have the OutBack FLEXnet DC installed? There could
be more data to review to try and get a sense of what the issue may
be. (shunt data, historical VDC data, any battery charging via grid?)
If the system has more than one Classic 200 are they connected and
set
up in "Follow Me" mode?
Any chance the charge controller or inverter/charger tried to
initiate
an equalization charge?
Does the system have any DC loads or generation sources (other than
the charge controller and inverter/charger) connected directly to the
battery system or anywhere on the DC bus?
Best regards,
----MATT
Matthew Sirum
P.O. Box 1227
Greenfield, MA 01302-1227 USA
phone: +1.413.773.0611
email: MatthewSirum at gmail.com
---------- Original Message Below ----------
[RE-wrenches] Over voltage error message
Drake drake.chamberlin at redwoodalliance.org
Mon Jul 17 05:36:46 PDT 2017
Hello Wrenches,
My client reported seeing an overvoltage error message on her Mate 3
on a Radian system. The Radian is selling to the grid and is being
fed by a Midnite Classic 200. It has shown two spikes so far, the
last one going to 67 volts and lasting 1 second. The batteries are
Concorde AGM, 305 AH.
Does this momentary spike seem like a problem or a warning of
problems to come?
Thanks,
Drake
_______________________________________________
List sponsored by Redwood Alliance
List Address: RE-wrenches at lists.re-wrenches.org
Change listserver email address & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
List-Archive:
http://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/maillist.html
List rules & etiquette:
www.re-wrenches.org/etiquette.htm
Check out or update participant bios:
www.members.re-wrenches.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20170718/1d6f4803/attachment-0002.html>
More information about the RE-wrenches
mailing list