[RE-wrenches] Pilot Hole Template

Thu Dec 13 08:37:20 PST 2012

Sounds like you already have the equipment.  But perhaps next time consider
DPW’s Easy Feet.  They are made to tech-screw right into the decking without
having to hit the truss.  Come pre-made with EPDM.  Just snap a line, set
and screw.  Obviously you will need to do some math to make sure your
decking material is substantial as well as anchored well to the blue board.
I have not used them yet, but will be putting up 20kW next month and will
report back.  That being said, anybody else have experience to report with
them?

Best regards,

Mark Dickson,

NABCEP Certified Solar PV Installer ™

Oasis Montana Inc.

  _____  

From: re-wrenches-bounces at lists.re-wrenches.org
[mailto:re-wrenches-bounces at lists.re-wrenches.org] On Behalf Of Jesse Dahl
Sent: Wednesday, December 12, 2012 1:33 PM
To: RE-wrenches
Subject: Re: [RE-wrenches] Pilot Hole Template

Thanks Chris,

I did the same as far as verifying layout of the beams, they are all the
same center to center, so that helps when snapping lines on the roof, we've
been using the quickmount jig for a few hours and haven't missed yet, so I
think we got it.  

Thanks all!

Jesse  

Sent from my iPhone

On Dec 12, 2012, at 1:38 PM, "Chris" <chris at solarwindworks.com> wrote:

Hi Jesse,

We just finished a similar roof mount project but had the good fortune to be
going into 6x14 beams at “ 48” o.c. “. I put the on center dimension in
quotes loosely, and spent a couple hours prior to drilling the first hole
checking layout of the beams, directly under where we’d be drilling. The
ceiling rafters varied in layout an inch to 8” so this paid off!!!

We used a 12” x 3/16” pilot bit, for our 8” Simpson SDS galv lags. I
eyeballed the angle into the beam, approx 10°, as we had 4 bolts in each
1.5” pipe flange base to land into the beams. The trick is having the 8” lag
bolt follow the hole into the 2x6 pine decking and beam. This wasn’t as hard
to do as we first thought it would be, and didn’t miss a one.

Hitting a 3x10 is going to be trickier, and your jig should help immensely. 

Sincerely,

Chris Worcester

Solar Wind Works
NABCEP Certified PV Installer
Phone: 530-582-4503
Fax: 530-582-4603
www.solarwindworks.com <http://www.solarwindworks.com/> 
chris at solarwindworks.com
"Proven Energy Solutions"

From: re-wrenches-bounces at lists.re-wrenches.org
[mailto:re-wrenches-bounces at lists.re-wrenches.org] On Behalf Of Jesse Dahl
Sent: Wednesday, December 12, 2012 7:54 AM
To: RE-wrenches
Subject: Re: [RE-wrenches] Pilot Hole Template

Since this job was a spec job and the materials are already here, I need to
use the quick mount, so.  I took a quick mount, inserted a 1/2" EMT coupling
(after some filing) and stuck a 8" piece of 1/2" EMT in the coupling Nd
tightened it down. Checked it with my square to ensure it is coming out of
the flashing square to the world.  I haven't drilled a hole yet, but will
update.  

Jesse

Sent from my iPhone

On Dec 12, 2012, at 8:03 AM, Jason Szumlanski <jason at fafcosolar.com> wrote:

We just completed a job with Eco-65's. It took about 12 man-days to install
200 of the base plates and L-Feet on a flat roof with wood blocks on a metal
deck with about 3" total from the rolled roof surface to the metal deck. We
custom-cut patches to go over the metal flashing supplied with the base
plate. 

Email me privately if you would like some pictures.

The materials are not cheap, but the installation was quite smooth and did
not require getting into the drop-ceiling or displacing office workers
below. We used 6" OMG extra heavy duty fasteners (part no. XHD006B).

Jason Szumlanski 

Fafco Solar 

On Wed, Dec 12, 2012 at 8:52 AM, Will White <William.White at realgoods.com>
wrote:

Have you looked at EcoFastens Eco-65 plate?  We used them on a roof similar
to what you’ve got and went right into the 2x6 so we didn’t have to go into
the structural members.  They’ve got a flashing that will work with asphalt
roofs.

Just make sure you get the right length fasteners so it doesn’t go through
the finished ceiling inside.

Thanks,

Will

____________________________________________________________________________
______________

Will White

Regional Field Operations Manager – New England

Real Goods Solar

64 Main St.

Montpelier, VT 05602

Tel: (802) <tel:%28802%29%20223-7804>  223-7804

Cell: (802) <tel:%28802%29%20234-3167>  234-3167

www.realgoodssolar.com <http://www.realgoodssolar.com/> 

From: re-wrenches-bounces at lists.re-wrenches.org
[mailto:re-wrenches-bounces at lists.re-wrenches.org] On Behalf Of Jesse Dahl
Sent: Tuesday, December 11, 2012 9:01 PM
To: RE-wrenches
Subject: [RE-wrenches] Pilot Hole Template

Hello,

The roof I'm currently working on is not a typical roof.  The construction
is as follows:

2"x6" tongue and groove exposed inside, with 4 inches of foam (blue board)
and on top of that 3/4" plywood with asphalt shingles on top of that.

I'd like to make a template to ensure that my pilot bit doesn't wander when
I'm going through the blue board.  If I miss the beams inside, the hole or
the lag would be exposed.  

Anybody run across this? Ideas?  I thought of maybe using a qucikmount
flashing, with a short section of EMT attached to help guide the bit....

Thanks!

Jesse

_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches at lists.re-wrenches.org

Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive:
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org

_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches at lists.re-wrenches.org

Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive:
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org

_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches at lists.re-wrenches.org

Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive:
http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20121213/fb4a7716/attachment-0003.html>