[RE-wrenches] battery venting

[JRQ]

I am doing this project in India. The cost structures here are a great deal more constrained that what we're used to. Using AGM batteries is going to be a deal-breaker with the client as far as cost. 

I also don't know if I can persuade the client to ship anything additional from the US. We pay more for electrical stuff, and then shipping adds quite a bit more on top. I've sold them on the idea of an Outback GTFX inverter on the basis of its functionality in a backup setup, but, for instance, I'm having a hard time convincing them that an E-Panel and a listed combiner box are a good idea, rather than just cobbling the BOS enclosures together from locally available breakers and PVC j-boxes. I also may end going with a indian-made PWM CC rather than a FM60. The quality of electrical work here is abysmal. I'm not sure if I can successfully make an argument on the grounds of somewhat contingent safety concerns, or even less on engineering standards.

So I'm wondering: are there parameters that constrain the bending of a venting pipe and the maximum angle from plumb that the pipe should take? And does the pipe diameter play a role in those parameters?

Jeffrey Quackenbush
NABCEP Certified PV Installer
Peripatetic Solar Technician


________________________________
 From: Allan Sindelar <allan at positiveenergysolar.com>
To: re-wrenches at lists.re-wrenches.org 
Sent: Saturday, December 31, 2011 8:42 PM
Subject: Re: [RE-wrenches] battery venting
 

Jeff,
I would use a Power Vent by Zephyr Industries. In addition to a 12V
    or 48V fan, his units have a built-in backdraft damper. Negative
    building pressure under certain conditions would be a concern of
    mine, so I wouldn't rely on angle to ensure exhaust always travels
    up and out.
Allan


 Allan Sindelar
Allan at positiveenergysolar.com
NABCEP Certified Photovoltaic Installer
NABCEP Certified Technical Sales Professional
New Mexico EE98J Journeyman Electrician
Positive Energy, Inc.
3201 Calle Marie
Santa Fe, New Mexico 87507
505 424-1112
www.positiveenergysolar.com 

 
On 12/31/2011 7:59 AM, JRQ wrote: 
Wrenches,
>
>
>I'm looking at a potential battery backup system wtih a 200 AH @48V flooded battery bank in the basement electrical room of a 3 story building. There is a window in the electrical room. The batteries will be located about 10' from an outdoor wall. The building is all reinforced concrete, so I can not run a vent pipe vertically from the batteries. Does anyone have a rule of thumb for how much the vent pipes can be angled from the batteries? Would it be more lenient for short sections of pipe (say <2') versus one long angled piece from the batteries? My instinct would be to keep the pipe no more than 45˚ from plumb.
>
>
>Or with bending the vent pipe: does anyone have a best-practice rule for the sum of the angles of bends?
>
>
>Thanks,
>Jeffrey Quackenbush
>NABCEP Certified PV Installer
>Peripatetic Solar Technician
>
>
>
>________________________________
> From: Drake <drake.chamberlin at redwoodalliance.org>
>To: re-wrenches at lists.re-wrenches.org 
>Sent: Saturday, December 31, 2011 8:08 PM
>Subject: [RE-wrenches] Pole Mount PVC
> 
>
>Hello Wrenches,
>
>With pole mount systems, It looks cleaner and is safer
                to run the PVC
                conduit down the pole into the concrete, and use a 90
                degree elbow to
                come out through the side of the anchor underground. 
                This way, the
                pipe is protected from mechanical damage, and there is
                nothing to trip
                over when adjusting the array for seasonal tilt.  
>
>I was told that some building departments will not allow
                this.  Has
                anyone had a problem with using this method, either
                technical or
                legal?   How do you like to route your conduits?
>
>Thank you,
>
>Drake 
>
>Drake Chamberlin          
>ATHENS ELECTRIC LLC
>OH License
                    44810         
>CO license 3773
>NABCEP Certified PV
>
>_______________________________________________
>List sponsored by Home Power magazine
>
>List Address: RE-wrenches at lists.re-wrenches.org
>
>Options & settings:
>http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
>
>List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
>
>List rules & etiquette:
>www.re-wrenches.org/etiquette.htm
>
>Check out participant bios:
>www.members.re-wrenches.org
>
>
>
>
>
_______________________________________________
List sponsored by Home Power magazine List Address: RE-wrenches at lists.re-wrenches.org Options & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out participant bios: www.members.re-wrenches.org 
_______________________________________________
List sponsored by Home Power magazine

List Address: RE-wrenches at lists.re-wrenches.org

Options & settings:
http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org

List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org

List rules & etiquette:
www.re-wrenches.org/etiquette.htm

Check out participant bios:
www.members.re-wrenches.org
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20111231/562e7b9c/attachment-0004.html>