[RE-wrenches] Dangerous installs/installers..

Jesse Dahl dahlsolar at gmail.com
Sat May 7 11:28:13 PDT 2011


I am in the process of doing just that. Along with explanations of why what was there was wrong. The list keeps growing and growing.....

Jesse

Sent from my iPhone

On May 7, 2011, at 11:21 AM, "Joel  Davidson" <joel.davidson at sbcglobal.net> wrote:

> Except for the renewable energy equipment, I saw poor wiring throughout India, soon to be the most populated country in the world. As my Arkansas Ozark mountain neighbor with poor wiring use to say about poverty of the mind, "Poor folks have poor ways." I hope you left a wiring diagram of a properly designed system.
>  
> Joel Davidson
>  
> ----- Original Message -----
> From: Jesse Dahl
> To: RE-wrenches
> Sent: Friday, May 06, 2011 11:45 PM
> Subject: [RE-wrenches] Dangerous installs/installers..
> 
> Wrenches,
> 
>  The other day on my travels, I came across a very scary small stand-alone hunting shack install.  All the wiring is cut extension cords and some UF, the cable from the charge controller to the batteries is an extension cord with the 14s paralleled.   mice chewed wire, splices taped and laid on the ground, mis matched modules (least of the problems). not a disco or OCPD to be seen. 
> 
> Also a 500W wind generator 100 yards from the battery bank, feed with #10s and then spliced to #12s (most of it just laying    on the ground.  
> 
> Now I think the owner should have some    responsibility to stop work when the see things this awful, but what can/should we as an industry do about this? What do we say to people that install stuff like this? Take them to court?
> 
> A small 2500w with surge of 5000w inverter was used here with 6 paralleled 12V deep cycle batteries. Powering a few lights and a vacuum at first, a well pump was added later. I could see the lights and vacuum, but a pump?  How do you go about wiring the output of an inverter like this?  From a receptacle on the inverter to what? This guy cut an extension cord off and splice it to some NM and ran it inside to the loads. No breaker, I just can't get over the fact this guy sleeps at night...
> 
> 
> You should see the photos of this mess...
> 
> 
> Thank you for your thoughts,
> 
> 
> 
> Jesse
> 
> Sent from my iPhone
> _______________________________________________
> List sponsored by Home Power magazine
> 
> List Address: RE-wrenches at lists.re-wrenches.org
> 
> Options & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
> 
> List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
> 
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
> 
> Check out participant bios:
> www.members.re-wrenches.org
> 
> _______________________________________________
> List sponsored by Home Power magazine
> 
> List Address: RE-wrenches at lists.re-wrenches.org
> 
> Options & settings:
> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org
> 
> List-Archive: http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org
> 
> List rules & etiquette:
> www.re-wrenches.org/etiquette.htm
> 
> Check out participant bios:
> www.members.re-wrenches.org
> 
-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org/attachments/20110507/dacbe3d3/attachment-0004.html>


More information about the RE-wrenches mailing list