Wire for PV plugs: 7 strand or 37 strand? [RE-wrenches]
Darryl Thayer
daryl_solar at yahoo.com
Fri May 16 05:19:34 PDT 2008
Hi
I was under the impression that the connectors/tools
were only approved for 7 strand?
Darryl
--- "Jay Peltz, Peltz Power" <jay at asis.com> wrote:
>
> Hi Mick,
>
> Been making my own for years.
>
> #10 7 strand ( over kill for most things) works
> fine in the new MC4
> connectors
>
> jay
>
> peltz power
> On May 15, 2008, at 10:07 AM, Mick Abraham wrote:
>
> >
> > Hi, Wrenchies~
> >
> > I'm nearly ready to start building my own plug
> leads to match the new
> > style PV modules. Multi-Contact sells a 37 strand
> #10 wire...and I
> > think
> > the strands are tinned.
> >
> > Common #10 sunlight resistant wire has only 7
> strands...fatter ones...
> > untinned. I would like to use up my remaining
> stock of 7 strand, but
> > only if it will work OK with the plugs. Please
> advise, Wrenches.
> >
> > I asked Ken Jeby (sales rep for Lou Marks & Sons)
> about this. He said
> > that 7 strand works A-OK, is widely used for this,
> and is all that he
> > can readily supply. He also said that 37 strand
> would be more
> > difficult
> > to work with...
> >
> > I could switch over to 37 strand just to be on the
> safe side, but the
> > Multi-Contact material is a bit more expensive,
> 1000 feet per
> > spool, and
> > not available in white.
> >
> > Perhaps I should dust off my contact information
> for Anixter Wire.
> > Perhaps one of you could suggest a source for the
> fine strand
> > material.
> > Or perhaps I should just stick with 7 strand and
> not worry about it.
> >
> > Thanks as always,
> >
> > Mick Abraham, Proprietor
> > www.abrahamsolar.com
> >
> >
> > - - - -
> > Hosted by Home Power magazine
> >
> > To send a message: RE-wrenches at topica.com
> >
> > Archive of previous messages:
> http://lists.topica.com/lists/RE-
> > wrenches/read
> >
> > List rules & how to change your email address:
> www.mrsharkey.com/
> > wrenches/etiquette.php
> >
> > Check out participant bios:
> www.mrsharkey.com/wrenches/
> >
> > Moderator: michael.welch at homepower.com
> >
>
>
> - - - -
> Hosted by Home Power magazine
>
> To send a message: RE-wrenches at topica.com
>
> Archive of previous messages:
> http://lists.topica.com/lists/RE-wrenches/read
>
> List rules & how to change your email address:
> www.mrsharkey.com/wrenches/etiquette.php
>
> Check out participant bios:
> www.mrsharkey.com/wrenches/
>
> Moderator: michael.welch at homepower.com
>
>
>
>
- - - -
Hosted by Home Power magazine
To send a message: RE-wrenches at topica.com
Archive of previous messages: http://lists.topica.com/lists/RE-wrenches/read
List rules & how to change your email address: www.mrsharkey.com/wrenches/etiquette.php
Check out participant bios: www.mrsharkey.com/wrenches/
Moderator: michael.welch at homepower.com
--^----------------------------------------------------------------
This email was sent to: michael.welch at re-wrenches.org
EASY UNSUBSCRIBE click here: http://topica.com/u/?bz8Qcs.bz9JC9.bWljaGFl
Or send an email to: RE-wrenches-unsubscribe at topica.com
For Topica's complete suite of email marketing solutions visit:
http://www.topica.com/?p=TEXFOOTER
--^----------------------------------------------------------------
More information about the RE-wrenches
mailing list